Background/Aim. Dental education has developed over the years, and various technologies have been included. Considering the fact that mobile devices are an imperative of modern time, the aim of our research was to evaluate effectiveness of Mobile-Aided Learning on practical administering the inferior alveolar nerve block (IANB). Methods. This prospective study involved 34 students who were randomly divided into two groups: G1 (control) group with 16 students and G2 (study) group with 18 students. Students of both groups previously successfully completed theoretical and practical training provided by the curriculum. For the purpose of additional education, students of the G2 group used a mobile application for 3D simulation of local anesthesia (Mobile-Aided Learning) outside the dental office for a period of one semester. After that, all students completed a post-clinical questionnaire. Results. The average time for performing anesthesia by participants in the G1 group was 70.54 ? 20.16 seconds, while in the G2 group it was 57.13 ? 17.45 seconds, which was significantly shorter (p ? 0.05). A successful anesthesia application was higher in the G2 group (83.3%) compared to the G1 group (75%). The results of the post-clinical test questionnaire also indicated difference in the mean values of the responses to all questions, which was in favor of the G2 group participants. Conclusion. Application of Mobile-Aided Learning showed a significantly higher efficiency in student education for practical implementation of the IANB.
Background and Objectives: The aim of this study was to clinically evaluate the primary and secondary stability of dental implants with different macrodesigns using resonance frequency analysis and to determine whether implant design and length influence implant stability. Materials and methods: This study included 48 healthy patients receiving dental implants, and a pre-implant planning protocol was used, which involved detailed bone analysis, clinical examinations, and Cone beam computed tomography (CBCT) analysis. The implants were of various types and dimensions (Alpha-Bio Tec (Israel), DFI, SPI, and NEO), and the surgical procedures were performed using standard methods. Implant stability was measured using resonance frequency analysis (RFA) immediately after placement and after 3, 6, and 12 months. The total number of implants placed in all patients was 96. Results: The average primary stability value for 10 mm SPI implants placed in the maxilla was 68.2 ± 1.7 Implant Stability Quotient (ISQ) units, while for 10 mm NEO implants, it was 74.0 ± 0.9. The average primary stability value for a 10 mm DFI implant placed in the mandible was 72.8 ± 1.2 ISQ, while for a 10 mm NEO implant placed in the mandible, it was 76.3 ± 0.8 ISQ. Based on the Friedman ANOVA test, the differences in the stability measurements for the 10 mm and 11.5 mm SPI implants and for the 10 mm and 11.5 mm NEO implants in the maxilla on day 0 and after 3, 6, and 12 months were significant at p < 0.05. Similarly, based on the Friedman ANOVA test, the differences in the stability measurements for the 10 mm and 11.5 mm DFI implants and for the 10 mm and 11.5 mm NEO implants in the mandible on day 0 and after 3, 6, and 12 months were significant at p < 0.05 (p = 0.00000). Conclusions: Universal tapered implants of the NEO type stood out as the optimal choice, as they provided statistically significantly higher primary stability in both soft and hard bone types compared to other implants. The implant length did not significantly affect this stability.
Background: Prefabricated zirconia posts can contribute to increasing the fracture resistance of the endodontically treated teeth. Purpose. This in vitro study compared the fracture resistance of endodontically treated central maxillary incisors prepared with 2mm ferrule length to the ones without ferrule. Material and methods: Twenty-four caries-free maxillary central incisors were divided into 2 groups of 12. In group A circumferential external dentin shoulders were prepared for 2mm external dentin ferrule length. There was no ferrule preparation in Group B. Zirconia VALLPOST BO-S (Ø 1,6mm), Ljubljana, Slovenia were used with retention forms in the coronary part. Core build-up was made of pressed ceramics (IPS e.max Press, Ivoclar, Liechtenstein). Crowns were manufactured from the same ceramic material (IPS e.max Press, Ivoclar). After root canal treatment and post space preparation, all posts were cemented with an adhesive resin cement (Multilink Automix, Ivoclar). The specimens were embedded in acrylic resin blocks (ProBase Polymer/Monomer, Ivoclar) and loaded at an angle of 45o to the long axis in an Instron Testing Machine 4301 (Instron Corp., USA) at a crosshead speed of 1mm/min until fracture. Fracture patterns and loads were recorded. A significance level of p<0.05 was used for all comparisons. Two-way analysis of variance was used for statistical analysis. Failure patterns were analyzed with the optical microscope Stereo Discovery V.8 (Carl Zeiss, Germany) and compared using the chisquare nonparametric test. Results: The mean values (±SD) of fracture loads (N) for the Groups A and B were 664.63N (±49.14) and 519.36N (±71.65) recpectively. Significantly lower failure loads were recorded for the specimens in the group B. Failure patterns within the groups revealed non-catastrophic failure in 70% of the specimens for group A and 85% for group B. Conclusions: Within the limitations of this in vitro study, it can be concluded that zirconia VALLPOST BO-S (Ø 1,6mm) with press-ceramic cores and crowns, can be used for restoration of endodontically treated teeth. The teeth prepared with 2mm external dentin ferrule length were found to be more fracture resistant than teeth without ferrule.