In a batch reactor, the EF advanced oxidation decolorization of aqueous solutions of methyl orange MO, a commercial azo reactive textile dye, was investigated in the presence of two different electrodes. The evaluation included various operational variables such as the I_C current intensity (60 mA, 80 mA, and 100 mA), initial concentration of pollutant MO (20 mg/L, 40 mg/L, and 60 mg/L), initial pH of solution (3, 5, and 7), temperature of solution (20 °C, 30 °C, and 50 °C), and initial concentration of catalyst [Fe²⁺] (0.1 mM, 0.2 mM, and 0.3 mM) on the discoloration rate. A Box-Behnken Design of Experiment (BBD) was used to optimize the parameters that directly affect the Electro-Fenton (EF) process. Under the optimal experimental conditions such as [Fe²⁺] = 0.232 mM, pH = 3, I_C = 80 mA, [MO] = 60 mg/L, and T = 30 ± 0.1 °C, the maximum discoloration rate achieved was 94.9%. The discoloration of the aqueous MO solution during the treatment time was confirmed by analysis of the UV-visible spectrum. After a review of the literature on organic pollutant degradation, the EF system provided here is shown to be one of the best in terms of discoloration rate when compared to other AOPs.

The objective of this study is to valorize Papaver rhoeas L. from the Taounate region of Morocco by determining the total polyphenol content (TPC), the total flavonoid content (TFC) and the antioxidant and antimicrobial activities of four organs. The quantification of TPC and TFC in root, stem, leaf and flower extracts (RE, SE, LE and FE, respectively) was estimated by the Folin–Ciocalteu reaction and the aluminum trichloride method, respectively. Two tests were used to assess antioxidant power: the DPPH test and TAC assay. The antimicrobial activity was studied against five pathogenic bacteria and yeast, using two methods: disk diffusion and microdilution. The TPC in LE and LF was twice as high as that in RE and SE (24.24 and 22.10 mg GAE/g, respectively). The TFC values in the four extracts were very close and varied between 4.50 mg QE/g in the FE and 4.38 mg QE/g in the RE. The LE and FE showed low DPPH values with IC50 = 0.50 and 0.52 mg/mL, respectively. The TAC measurement revealed the presence of a significant amount of antioxidants in the studied extracts, mainly in LE and FE (6.60 and 5.53 mg AAE/g, respectively). The antimicrobial activity results revealed significant activity on almost all of the tested strains. The MIC of FE and SE against E. coli 57 was 1.56 and 0.78 mg/mL, respectively, while against the S. aureus it was 50 and 25 mg/mL, respectively. The low MLC value (1.56 mg/mL) was recorded against E. coli 57 by RE and SE.

Providing efficient and environmental friendly ways to recover lignocellulosic waste remains a challenge around the world. In this study, citric acid-catalyzed hydrothermal carbonization (CHTC) was coupled with pyrolysis to convert date seed (Ds) into adsorbent material. In this regard, a central composite design (CCD) using response surface methodology (RSM) was developed to examine the influence of temperature, reaction time, and catalyst dose on the mass yield (Y_m()) and carbon retention rate (C_RR()) in the produced hydrochars. The optimized hydrochar (OHC-Ds) was obtained under optimal conditions (200°C, 120min, 20mg) and characterized by a Y_m() and C_RR() of 59.71 and 75.84, respectively. Chemical activation by KOH of OHC-Ds followed by pyrolysis at 600°C resulted in an active material (AOHC-Ds) rich in carbon and characterized by a high specific surface area of 1251.5m²/g, with the dominance of mesopores, as well as an amorphous structure comparable to graphite shown by X-ray diffraction (XRD) analysis. Adsorption experiments of two dyes on AOHC-Ds showed a high maximum adsorption capacity (Q_m) of 657.89mgg⁻¹ for methylene blue (MB) and 384.61mgg⁻¹ for methyl orange (MO) compared to other conventional adsorbents. This result is due to the low acidity (pH_pzc) of the surface of AOHC-Ds, which equals 6.75, and its surface, which is also rich in oxygenated functional groups such as (-OH), (C=O), and (C-O) shown by FTIR analysis. These results suggest that the coupling of CHTC and KOH activation followed by pyrolysis is an encouraging way to prepare an efficient and inexpensive adsorbent to remove dyes in wastewater.

This research aimed to measure the impact of provenance on the yield, chemical profile and antimicrobial activity of Rosmarinus officinalis essential oil (EO) collected from cultivated and wild plants from two different regions in Morocco (Fez and Figuig). The chemical composition analysis was...

Purpose: The inhibition effect ofFoeniculum vulgareseeds’ (FVS) extract on the corrosion of mild steel in acidic medium was studied using weight loss, electrochemical impedance spectroscopy and Tafel polarization, as well as the surface morphology of the mild steel.Design/methodology/approach: Weight loss measurements, potentiodynamic tests, electrochemical impedance spectroscopy studies and gas chromatography/mass spectrometry and scanning electron microscopy analysis of FVS extract were performed.Findings: FVS extract acts as a good inhibitor for the corrosion of mild steel in 1.0 M HCl. The inhibition efficiency increases with the increase in inhibitor concentration but decreases with the increase of temperature.Practical implications: FVS extract was observed to play an important role in the corrosion inhibition of mild steel in acidic solution.Originality/value: This paper is intended to be added to the family of green inhibitors which are highly efficient inhibitors and can be used in the area of corrosion prevention and control.

Coagulation–flocculation, historically reliant on simple inorganic salts, has evolved into a technically sophisticated process that is central to the removal of turbidity, suspended solids, organic matter, and an expanding array of micropollutants from complex wastewaters. This review synthesizes six decades of research, charting the transition from classical aluminum and iron salts to high-performance polymeric, biosourced, and hybrid coagulants, and examines their comparative efficiency across multiple performance indicators—turbidity removal (>95%), COD/BOD reduction (up to 90%), and heavy metal abatement (>90%). Emphasis is placed on recent innovations, including magnetic composites, bio–mineral hybrids, and functionalized nanostructures, which integrate multiple mechanisms—charge neutralization, sweep flocculation, polymer bridging, and targeted adsorption—within a single formulation. Beyond performance, the review highlights persistent scientific gaps: incomplete understanding of molecular-scale interactions between coagulants and emerging contaminants such as microplastics, per- and polyfluoroalkyl substances (PFAS), and engineered nanoparticles; limited real-time analysis of flocculation kinetics and floc structural evolution; and the absence of predictive, mechanistically grounded models linking influent chemistry, coagulant properties, and operational parameters. Addressing these knowledge gaps is essential for transitioning from empirical dosing strategies to fully optimized, data-driven control. The integration of advanced coagulation into modular treatment trains, coupled with IoT-enabled sensors, zeta potential monitoring, and AI-based control algorithms, offers the potential to create “Coagulation 4.0” systems—adaptive, efficient, and embedded within circular economy frameworks. In this paradigm, treatment objectives extend beyond regulatory compliance to include resource recovery from coagulation sludge (nutrients, rare metals, construction materials) and substantial reductions in chemical and energy footprints. By uniting advances in material science, process engineering, and real-time control, coagulation–flocculation can retain its central role in water treatment while redefining its contribution to sustainability. In the systems envisioned here, every floc becomes both a vehicle for contaminant removal and a functional carrier in the broader water–energy–resource nexus.