Liqun Hou

Dr. Liqun Hou


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 June 2018 in IEEE Access
Verified
Journal Article
Open access
LHLiqun Hou
Liqun Hou
STShudong Tan
Shudong Tan
ZZZhijuan Zhang
Zhijuan Zhang
NBNeil W. Bergmann
Neil W. Bergmann
As the backbone of Industrial Internet of Things (IIoT), wireless sensor networks (WSNs) are generally powered by batteries with limited energy, which constrains the continuous operations of WSNs and IIoT. Energy harvesting is a promising solution for this problem. Industrial plants have many hot pipelines or walls, and the temperature is one of the critical parameters to be monitored in industrial processes. This paper developed a novel thermal energy harvesting WSN node for temperature monitoring in IIoT. The feasibility of the presented self-powered WSN node is experimentally verified for a range of different sleep periods of the device. These results demonstrate that the designed boost circuit has an energy conversion rate of about 27%, and the proposed thermal energy harvester is able to indefinitely power a commercial WSN node when the sleep period of the device exceeds 16s, which represents a duty cycle of 5.4%.

26 December 2016
Verified
Conference Paper
Closed access
LHLiqun Hou
Liqun Hou
STShudong Tan
Shudong Tan
The energy-constrained battery has become one key issue that hinders the application of industrial wireless sensor networks (IWSNs). Energy harvesting is a promising solution for this problem. After comparing several energy harvesting approaches, thermoelectric energy harvesting for IWSNs is explored in this paper. The behavior of commercial thermoelectric module is analyzed based on its finite element analysis models. The corresponding experimental setup including thermoelectric module, conversion circuits, and sensor node is then built up and evaluated. To tackle the problem of current design, the future work and possible solutions are discussed as well.

15 September 2022 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
LHLiqun Hou
Liqun Hou
LLLan Liu
Lan Liu
GMGuopeng Mao
Guopeng Mao
Compared with a wired machine fault diagnosis system, a wireless one based on wireless sensor networks (WSNs) has many inherent merits, such as low cost and ease of installation. However, the limited bandwidth and battery energy of WSNs will impede the high-speed data collection and transmission required in the machine fault diagnosis system. To address this challenge, this article proposes a novel machine fault diagnosis method based on separable convolution and WSNs with sensor computing. First, a lightweight 1-D separable convolution network fault diagnosis model is designed and embedded on the WSNs sensor node. Machine fault diagnosis is then completed on the sensor node, and only the diagnosis result is transmitted in the WSNs to reduce transmission data. A set of experiments have been conducted on the experimental setup to evaluate the proposed method. The results show that the accuracy of the proposed method can reach 98.3%, and the payload transmission data of the WSN decrease from 2048 bytes to 2 bytes, while the node’s energy consumption saves about 15%. Compared with traditional 1-D convolutional neural network (CNN) and 1-D residual network (ResNet), the proposed method is more suitable for the application on resource-constrained WSNs nodes.

6 January 2020 in Engineering Research Express
Verified
Journal Article
Closed access
LHLiqun Hou
Liqun Hou
WCWeinan Chen
Weinan Chen
Energy harvesting is a promising alternative to batteries for autonomous WSN nodes. Although there are various energy harvesting methods using ambient energy sources, this research is focused on thermal energy harvesting because there are abundant thermal sources in industrial sites. As only several mW can be obtained by a thermal energy harvester based on a thermoelectric generator (TEG), improvement of the energy conversion efficiency of the thermal energy harvester is essential. This paper proposes a novel maximum power point tracking (MPPT) method combining coarse adjustment and fine adjustment to enhance the energy conversion efficiency of the harvester. The Direct Adjustment (DA) method for MPPT is adopted in the coarse adjustment stage to avoid disconnecting TEG modules from conversion circuits, while an observation and self-optimization (O&SO) method for MPPT is used in the fine adjustment stage to avoid introducing perturbations and to maintain a stable output power at the maximum power point (MPP). After building up the system simulation model, a series of experiments are conducted to evaluate the proposed MPPT methods. The results show that the DA + O&SO method is an effective MPPT method for a WSN node powered by a TEG. It is able to enhance the regulation speed of the MPPT, improve the continuity of P out , and avoid the power oscillations around the MPP.

28 April 2017 in International Journal of Online and Biomedical Engineering (iJOE)
Verified
Journal Article
Open access
PDF file
LHLiqun Hou
Liqun Hou
STShudong Tan
Shudong Tan
LYLei Yang
Lei Yang
ZZZhijuan Zhang
Zhijuan Zhang
NBNeil Bergmann
Neil Bergmann
The feasibility of using thermal energy harvesting to power a wireless sensor node for temperature monitoring of industrial devices is explored and evaluated in this paper. The thermal energy harvesting equipment and energy conversion circuit have been designed and fabricated. A series of experiments with various sleep periods for the sensor node are undertaken. The experimental results show that the thermal energy harvesting equipment and energy conversion circuit are able to power a commercial wireless node when the sleep period of the node is more than 16s, equating to a duty cycle of 5.4%. The results also indicate that the wireless sensor network based on the proposed autonomous wireless sensor node can monitor the industrial device temperature successfully.

1 October 2018
Verified
Conference Paper
Closed access
XWXiaodong Wei
Xiaodong Wei
LHLiqun Hou
Liqun Hou
JHJunteng Hao
Junteng Hao
Mechanical equipment fault signals are mostly nonlinear and non-stationary signals. Processing these signals by Fourier transform and wavelet transform usually cannot obtain desired fault diagnosis results. In this paper, a machine fault diagnosis method based on Industrial Internet of Things (IIoT), industrial wireless sensor networks (IWSNs), Hilbert-Huang transform (HHT), and support vector machine (SVM) is proposed, in which HHT and SVM are used for fault feature extraction and fault diagnosis respectively. The proposed fault diagnosis approach by SVM is implemented and tested on the IWSN sensor node, while the fault feature extraction method using HHT is verified by MATLAB simulation. The effectiveness of the presented approach is evaluated by a set of experiments using bearing vibration data. The result indicates that the fault diagnosis accuracy of the presented method reaches 100% for four machine working conditions and 92% for five working conditions.