Structural health monitoring (SHM) systems may allow a reduction in maintenance costs and extend the lifetime of the structure. As a result, they are of interest to the research community. Ideally, the SHM methods should be low cost, while being able to detect and localize small levels of damage reliably and accurately. The fiber Bragg grating (FBG) sensors are light in weight, insensitive to electric and magnetic fields, and can be embedded. The edge filtering configuration for transduction allows the use of FBG for guided wave (GW) sensing. This sensitivity may be further enhanced through their application in the remote bonded configuration. This paper provides a proof-of-concept for the use of remotely bonded FBG for damage localization. In order to improve the computational efficiency, a particle swarm optimization (PSO) based algorithm is developed. The PSO allows a significant improvement in the computation time which makes it better suited for real-time damage localization. The proposed objective function is based on the exponential elliptical approach. First, the suitability of the PSO for damage localization is shown. Then the performance of the chosen objective function is compared with the brute-force algorithm as well as other objective functions found in the literature. The methodology is employed on a simple aluminum plate. The results indicate that indeed the objective function along with the PSO is suitable for damage localization. Also as the objective function is developed taking into consideration the specific challenges with the use of FBG sensors, performs better than the other objective functions as well as the brute force algorithm.
Optical fibers were previously demonstrated to propagate and detect acoustic modes that were converted from Lamb waves for structural health-monitoring applications; typically, a fiber Bragg grating sensor in the optical fiber is used to detect acoustic modes. Acoustic modes can transfer from one fiber to another through a simple adhesive bond coupler, preserving the waveform of the acoustic mode. This paper experimentally investigates the coherence of acoustic waves through the adhesive coupler, using a fiber ring resonator (FRR) configuration. This configuration was chosen because the wave coupled to the second fiber interferes with the original wave after it encircles the fiber ring. We performed this experiment using different geometries of optical fibers in the ring, including a standard single-mode optical fiber, a hollow silica capillary tube, and a large-diameter multi-mode fiber. The results demonstrate that the acoustic wave, when transferring through an adhesive coupler, interferes coherently even when the main and ring fibers are of different types. Finally, we demonstrate that the FRR can be applied for sensing applications by measuring the mode attenuations in the ring due to a changing external environment (water-level sensing) and measuring the optical-path length change in the ring (temperature sensing).
Guided waves (GW) allow fast inspection of a large area and hence have received great interest from the structural health monitoring (SHM) community. Fiber Bragg grating (FBG) sensors offer several advantages but their use has been limited for the GW sensing due to its limited sensitivity. FBG sensors in the edge-filtering configuration have overcome this issue with sensitivity and there is a renewed interest in their use. Unfortunately, the FBG sensors and the equipment needed for interrogation is quite expensive, and hence their number is restricted. In the previous work by the authors, the number and location of the actuators was optimized for developing a SHM system with a single sensor and multiple actuators. But through the use of the phenomenon of acoustic coupling, multiple locations on the structure may be interrogated with a single FBG sensor. As a result, a sensor network with multiple sensing locations and a few actuators is feasible and cost effective. This paper develops a two-step methodology for the optimization of an actuator–sensor network harnessing the acoustic coupling ability of FBG sensors. In the first stage, the actuator–sensor network is optimized based on the application demands (coverage with at least three actuator–sensor pairs) and the cost of the instrumentation. In the second stage, an acoustic coupler network is designed to ensure high-fidelity measurements with minimal interference from other bond locations (overlap of measurements) as well as interference from features in the acoustically coupled circuit (fiber end, coupler, etc.). The non-sorting genetic algorithm (NSGA-II) is implemented for finding the optimal solution for both problems. The analytical implementation of the cost function is validated experimentally. The results show that the optimization does indeed have the potential to improve the quality of SHM while reducing the instrumentation costs significantly.
Previous studies demonstrated coupling of acoustic guided waves from one optical fiber to another through a simple adhesive bond coupler. This paper experimentally utilizes such an adhesive bond coupler to easily extend an already existing sensor network. We experimentally demonstrate this concept for detecting simulated cracks growing from circular holes in a thin aluminum plate. A single, remotely bonded FBG sensor is used to detect the original crack growth, followed by the addition of other optical fiber segments using adhesive couplers to detect new crack growth locations on the plate. A laser Doppler vibrometer is also used to measure the guided wave propagation through the plate to verify that the changes in the FBG sensor measurements are due to the growth of the cracks.
In this paper the behavior of a cyanoacrylate (CA) bonded optical fiber acoustic signal coupler will be studied in detail. A stainless-steel mold was used to create a 2×2 CA coupler that transfers guided waves between two optical fibers. Four FBGs placed at each port were used to assess the repeatability, signal behavior, and performance of the coupler produced. Signal propagation through the network was mapped to determine how the initial acoustic signal traveled and subdivided through the fiber network. To examine the repeatability of the signal coupler interaction, the experiments were performed multiple times. Finally, the acoustic energy transferred through the coupler’s paths was calculated to assess the performance of the 2×2 coupler. The coupler successfully and repeatably transferred an acoustic signal from one optical fiber to another; however, the performance associated with the current coupler design was limited by relatively large excess and return losses. Improvements to the CA coupler design are then proposed from the results.
We measure the mode conversion of symmetric and anti-symmetric Lamb waves in a plate to longitudinal and flexural modes in an optical fiber, through an adhesive bond, using a high resolution 3D laser Doppler vibrometer.