Axis-flux wind generators are widely used in vertical axis wind turbines given their high generator diameter-to-length and power-to-weight ratios, flexible field and winding design, improved cooling, and possibility of modular construction. In this paper, an asymmetric-primary axis-flux hybrid-excitation generator (APAFHG) is proposed to provide a controllable maglev force that compensates for the ripple of axial force fluctuation. First, the operation principle of the proposed generator is introduced. No-load performance influenced by direct current (DC) excitation is obtained by using the 3D finite element method (3D-FEM). Second, the load performances are analyzed under two typical operation statuses, namely, symmetrical pure resistance load and $i_{d}=0$ control strategy load. An alternating current (AC) excitation method is then comparatively analyzed to increase the output power under the maximum armature current. Third, based on the dq axes dynamic mathematical model, the quantitative calculations of levitation force and torque characteristics are deprived and then tested and verified by using the finite element analysis results. These results show that the proposed generator can be implemented for the decoupling control operation of power and levitation forces and is suitable for vertical axis wind turbines.
A circularly-polarized (CP) rectangular dielectric resonator antenna (DRA) fed by a wideband feed network is introduced. The feed network is designed by using branch-line structure and named as wideband branch-line coupler (WBLC). The proposed WBLC delivers good impedance matching, equal power splitting and consistent 90° shifting over a wide bandwidth. It is demonstrated that for the presented rectangular CP DRA, the employment of the WBLC, in place of a conventional coupler with narrowband, provides improved characteristics in terms of circular polarization and impedance matching. The antenna prototype with the WBLC exhibits 3-dB axial ratio bandwidth of 47.69% and impedance bandwidth of 48.46% for VSWR ≤ 2.
The construction of hydropower stations has been expanding in China as a result of economic development and the improvement of people's lives. To save cost, the capacity of a single unit has been greatly increased, and many higher technical requirements have been presented for hydropower units, among which one of the key technologies is the thrust bearing. With the increase in single machine capacity, the pv value of the kinetic energy on the thrust bearing also increases, which will cause the bearing tile burning accident. Therefore, the thrust bearing needs to be designed to improve the bearing capacity. Instead of improving the traditional mechanical structure and using new materials, this paper proposes a levitation load reduction device for the thrust bearing to reduce the pv value of the kinetic energy on the thrust bearing. On the basis of kinetic energy analysis, the feasibility of the magnetic levitation load reduction device is analyzed. A repulsive maglev load reduction device suitable for hydropower units is designed; according to linear motor theory, a three-dimensional analytical model is established to analyze the levitation force, and an analytical calculation method is given. A finite element simulation model is built to study the effects of the primary electrical parameters, structural parameters, and material properties on electromagnetic forces, and the effect rules and the methods of optimal design are given. A small-scale prototype was developed, then tests were conducted to verify the feasibility and accuracy of the design and mechanism.
2 July 2021 in IEEE Transactions on Applied Superconductivity
The tiles burning accident may happen with the temperature rising because of the severe friction if the axial load was very big for the thrust bearing. We proposes using maglev technology to reduce the load for the thrust bearing to avoid the accident. Based on the principle of not coupling the original system, a disc electrodynamic maglev machine is designed, which will provides a normal repulsion as the levitation force to offset one part of the axial load for the bearing with the advantages of good self-stability and light secondary. The tangential force generated at the same time and is useless. The electrical and structural parameters both affect two forces. This paper studied the analytical calculation method, the relationship of the two forces, and the energies stored in the air-gap and expended in the secondary. Then the laws of parameters affecting the forces are obtained, which reveal the design method to improve the levitation force and decrease the tangential force. Based on the theoretical re-search, the Coreless superconductor primary armature is thought most suitable for this machine with higher y-axis component of magnetic field in air-gap. The FEA simulation model is used to verify the theoretical analysis.
1 June 2017 in IEEE Transactions on Plasma Science
Linear induction machines (LIMs) are widely used in the electromagnetic launch systems. Based on the MgB2 type superconducting wires, a superconductive LIM with an electrodynamic type structure (EDS) is proposed in this paper. The moving primary magnetic field induces eddy current in the conductor plate and the inductive eddy magnetic field acts back on the primary field. The lift force and thrust force will be produced between the primary and the secondary. Referred to the analysis of some famous researchers’ theory and achievements, an improved method is proposed and applied to MgB2 type superconducting LIM. The calculation results are obtained and compared with finite-element analysis. The results indicate the method is practical and valid, which can lead the design and save design time.
1 May 2023 in Journal of Physics: Conference Series
An asymmetric-primary axial-flux hybrid-excitation generator (APAFHG) has already been proposed to improve the starting performance of vertical axis wind turbines. However, the double-stator single-rotor structure causes a problem: different torque proportions create different rotor maglev forces, which will cause fluctuation and negatively impact the rotor bearing and even the operation of the wind power generation system. Therefore, a mathematical model considering the double-stator single-rotor structure and a proportional integral-based torque control strategy considering double-stator distribution are proposed in this paper to help APAFHG offer a good starting performance in vertical-axis wind power generation system and to stabilize maglev force generated by double-stator quadrature axis current simultaneously. Finally, the cooperation control of the maglev force and torque distribution is realized in MATLAB/Simulink, and the rotor maglev force will be relatively stable despite mechanical torque changes, which is a basis for the wind turbine to stably operate as the wind constantly fluctuates in vertical axis wind power system.