After being harvested, fresh apples and apricots have a high moisture content and are put through a drying process to reduce waste and lengthen shelf life. This study intends to evaluate the physicochemical parameters during moisture removal and product heating in order to conduct an experimental investigation of the convective drying of apples and apricots in a pilot drying installation. The drying agent’s temperature and/or speed can be adjusted using the pilot installation. About the raw materials: the apricots (Neptun variety) were dried and cut into halves, while the apples (Golden Delicious variety) were dried and cut into 4 mm thick slices. The fruits’ drying properties were observed at 50 °C, 60 °C, 70 °C, and 80 °C, air speeds of 1.0, 1.5, and 2.0 m/s, and relative air humidity levels of 40–45%. Findings of the ascorbic acid content, color, heating, and dimensional fluctuations are provided and examined. Increased air velocity and temperature had the expected effect of increasing water loss, solid gain, and shrinking. Depending on the drying conditions, different color characteristics were applied.

Concerns over the past few decades have focused, more than ever, on finding and implementing efficient, handy, and renewable sources to reduce pollution. Biomass, in general, and biomass from annual vine cuttings, are renewable sources that can be used by a large amount of the population. Biomass densification in the form of briquettes is an efficient method of obtaining a biofuel with the same characteristics as wood. The production of densified material as a briquette consists of sampling, drying naturally, chopping, grinding and briquetting the vine cuttings. The obtained results showed that the size of the briquettes met the requirements imposed by the standard, with a length between 185 mm and 400 mm and a diameter of 58 ± 0.75 mm, the humidity of the briquettes varying between 5.42%, at Sauvignon Blanc and 7.98% for Pinot Noir, while the durability of the briquettes registered minimum values of 98.17% for Muscat Ottonel and a maximum of 99.14% for Feteasca Neagra, and a unit density with values between 1227 kg/m³ for Feteasca Alba and 1389 kg/m³ for Pinot Noir. The conclusions of these experiments are promising, showing that the densification of biomass from vines cuttings qualifies within the standard requirements for obtaining a valuable biofuel.

The dehydration of agricultural products is a topic of research covering the preservation and conservation of the quality of agricultural and food items. The actual tasks of environmental protection include creating novel solutions to reduce the energy needs and exothermic consequences of the bulk of industrial processes. Due to the fact that air temperature and velocity in the seed layer are not uniform, the currently employed seed dryers have significant energy requirements and generate a lot of heat. A device that addresses this problem was developed and is now the subject of a patent application. The Coandă effect-based tronconic plates used in the dryer enable warm air to be dispersed uniformly throughout the product mass. Mathematical modeling was used for the design, operation, and optimization of the baffled drying unit. The investigations, which were conducted by modifying and observing the operational parameters (the velocity and temperature of the warm air) used four distinct types of seed with three different beginning moisture concentrations. Following the completion of the CFD simulation, the unit’s design was created in SolidWorks. The seed and air humidity were measured using sensors, and the air speed was measured using an anemometer. The current lines and fields were used to express the speed and temperature results. The unit with deflectors reduced the amount of heat released by up to 15.38% and reduced the amount of energy used by up to 14%.

The goodness-of-fit analysis performed over the results provided by a model presented in a previous paper proved that the theoretical data were very well correlated with the experimental data with regard to the traction force (with Pearson coefficient r² over 0.9); however, the model was less accurate in predicting traction efficiency, with r² = 0.203. In order improve the model and obtain a better fit between the theoretical and experimental data (especially for the traction efficiency), the model was updated and modified by taking into account the geometry of the tire cross section, which was considered to be a deformable ellipse. Due to the deformable cross section, the minor axis of the tire–ground contact super ellipse decreased compared with the previous model (from 0.367 m to 0.222 m), while the major axis increased (from 0.530 m to 0.534 m). As a result, different data for the traction force and traction efficiency were obtained. The effect of the wheel travel reduction (wheel slip) over the tire–soil shear area was also investigated, and the hypothesis of a constant shear area (independent of wheel slip) provided the most accurate results. The goodness-of-fit analysis performed using the data predicted by the modified model showed that the Pearson coefficient increased significantly with regard to the traction efficiency (from 0.203 to 0.838), while it decreased by only 2.7% with regard to the data for the traction force, still preserving a high value (r² = 0.896).

Hybrid seed drying technology, based on convection and microwave drying, is a modern method, and the research on the physical changes in cereal seed resulting from hybrid drying is still in its infancy. The aim of the present paper is to study the uniformity of the drying process by examining the physical changes occurring in corn seeds. An innovative drying equipment, combining convective and microwave drying, was used to dry corn seeds (variety DKC5068). The convective drying was performed during the pneumatic transport of the seeds, using hot air at a maximum temperature of 50 °C; the microwave-based drying was performed using 2.45 GHz microwaves. Thus, the seeds were volumetrically heated at a temperature which does not exceed 44 °C. The physical changes in corn seeds were measured in terms of moisture, volume, cracking and color. The results regarding the moisture and volume changes in the seeds during the drying process proved that moist seeds are more homogeneous than dry seeds. The change in volume also changed the stiffness of the seeds, which showed greater homogeneity after drying compared to wet seeds. Hybrid drying led to an average shrinkage of 8.76% compared with the original seed volume, while the percentage of seeds showing cracks after drying increased by 22%. Generally, the drying process also led to color changes, but in the case of hybrid drying the results were inconclusive. Hybrid drying of corn seeds requires a shorter time and does not significantly influence physical characteristics, compared to other drying technologies.

Worldwide, different strategies are being developed in order to ensure optimum conditions for the development and growth of economic competitiveness, as well as for increasing the quality of life and environmental protection. All these strategies are closely linked to the development and modernization of systems for producing energy from clean and renewable sources. In this context, the present paper presents the results of research regarding the evaluation of the sustainability of briquette production using biomass resulting from vine winter pruning as the raw material. An analysis of the scientific literature indicates that nearly 8 Mt of biomass would result from the over 7.4 million hectares of vine plantations in the world, biomass that could be valorized through densification in order to produce solid biofuels with a lower calorific value of more than 17 MJ/kg. This study examines the production of briquettes from vineyard winter pruning with consideration of two types of densification technologies: baling and natural drying of the tendrils, and collection, shredding, and artificial drying of the lignocellulose debris. The quality indices and energy consumption and energy efficiency of the briquettes were evaluated to determine their feasibility as an alternative fuel source. When designing the scientific endeavor, the following aspects were considered: defining the aim and objectives of the research; designing the research algorithm; collecting, preparing, and conditioning the biomass; conducting a chemical analysis of the briquettes; and evaluating the energy consumption and energy efficiency for producing the briquettes, taking into account two drying methods (natural and artificial drying). In the meantime, some specific laboratory equipment was designed and built for the artificial drying of biomass, evaluation of mechanical durability, measurement of energy consumption, etc. Analysis of the experimental data has led to the conclusion that the agricultural waste from vine pruning can constitute an important and sustainable source of energy in the form of briquettes that fulfill most of the requirements imposed by international standards.