The growth of the world's population increases the demand for fresh water, food, energy, and technology, which in turn leads to increasing amount of wastewater, produced both by domestic and industrial sources. These different wastewaters contain a wide variety of organic and inorganic compounds which can cause tremendous environmental problems if released untreated. Traditional treatment systems are usually expensive, energy demanding and are often still incapable of solving all challenges presented by the produced wastewaters. Microalgae are promising candidates for wastewater reclamation as they are capable of reducing the amount of nitrogen and phosphate as well as other toxic compounds including heavy metals or pharmaceuticals. Compared to the traditional systems, photosynthetic microalgae require less energy input since they use sunlight as their energy source, and at the same time lower the carbon footprint of the overall reclamation process. This mini‐review focuses on recent advances in wastewater reclamation using microalgae. The most common microalgal strains used for this purpose are described as well as the challenges of using wastewater from different origins. We also describe the impact of climate with a particular focus on a Nordic climate.
In the present document, we report the development of an analytical method consisting of a sequential direct-immersion/headspace solid-phase microextraction (DI-HS-SPME) followed by gas-phase chromatography and tandem mass spectrometry (GC-MS/MS) for simultaneous analysis of 4-chlorobenzyl alcohol, 2,6-dichlorobenzyl alcohol, 4-methoxybenzyl alcohol, 3,4-dimethoxybenzyl alcohol, pyridine, and 2,3-dimethylpyrazine in oilfield production waters. These compounds are under evaluation for use as phase-partitioning tracers in oil reservoirs. To the best of our knowledge, this is the first time SPME has been applied to the analysis of these compounds in production waters, or any other type of matrix where the compounds targeted are the base for a technical application. Relevant extraction parameters, such as the adsorbent phase of the fiber, direct immersion or headspace, addition of salt, temperature and time of extraction were investigated. The final optimal operation conditions consist on extracting 5 mL of sample at pH 9.0 with 1.8 g of NaCl with constant stirring during 5 minutes of DI-SPME followed by 15 minutes of HS-SPME at 70 °C using a DVB/CAR/PDMS (50/30 µm) fiber. The limits of quantification (LOQ), linearity, precision and accuracy of the method were evaluated. Analyses of the tracer compounds and recovery studies were also performed on production waters from 8 different oilfields of the Norwegian continental shelf. LOQs between 0.080 and 0.35 µg L−1 were obtained. The recovery yields of the method were consistently higher than 85% and RSDs less than 13%. None of the tracer compounds was found in the real samples processed, which is consistent with one of the requirements for an artificial tracer in an oilfield: absence or constant and low background in the traced fluid. The performance of the method developed, combined with its easiness to automate, introduce a new, accurate and cost-efficient technique to process the hundreds of samples required by an inter-well tracer test.
1 August 2018 in Journal of Petroleum Science and Engineering
Controlled release of aromatic mixtures to the atmosphere is a requirement for scented systems for indoor applications. The product must smell nice, but also be able to last, slowly releasing the perfume over time. Several adsorption materials have been used, for this purpose. In this study, cork was investigated as a potential perfume adsorbent for application in scented drawer sachets and equivalent products. Cork was selected due to its adsorption properties and because it is a natural, renewable, sustainable material. Granulated cork is a significant by‐product in cork industries and it was chosen for adsorption in this work. Linalool, an enantiomeric monoterpene alcohol and one of the main components of several essential oils, was selected as the model compound for adsorption studies.Activated carbon (AC) was used as the reference material. The sorption of linalool to granulated cork and AC was evaluated by HS‐SPME‐GC‐FID. The linalool isotherm on cork was shown to follow a Brunauer‐Deming‐Deming and Teller, Type IV model. The isotherm data on AC can be adjusted to Langmuir and Freundlich models. A maximum adsorption capacity of 3.9x103μg/g was achieved for AC. Desorption studies were performed. Linalool was still released from granulated cork after three equilibrium stages of desorption, whereas only two desorption values were obtained for AC from the equilibrium with highest linalool concentration. Thus, AC demonstrated good adsorption but not good desorption properties. Sorption and desorption studies of linalool from granulated cork, showed that granulated cork could be an excellent material allowing controlled release of the aroma.
This paper presents the results from the stability experiments carried out on a selected set of chemical compounds. These experiments represent one of the steps for their qualification as oil/water partitioning tracers for measurement of residual oil saturation in the inter-well region. Single-well chemical tracer tests (SWCTT) are a proven tool, frequent in the industry, to measure residual oil saturation (SO) in the near well region. SWCTT are "push-and-pull" tests where an oil/water partitioning ester will partially hydrolyze, generating a passive water tracer, often an alcohol. Oil saturation is then determined from the lag in back production experienced by the ester in relation to the passive water tracer produced during the test. Partitioning inter-well tracer tests (PITT) explore the same delay experienced by the partitioning tracer to determine SO in the swept volume between an injector and one or more producers in an oilfield. Unlike SWCTT, PITT are not frequently used in the industry, and a small number of compounds is qualified as tracer in this application. The development of new PITT tracers will help to widen the use of this technology, which has the potential to significantly contribute to enhance efficiency in oil production. To be used as oil reservoir PITT tracers, the candidate compounds must perform as required by the application under static stability and dynamic experiments. In this work, fifteen PITT tracer candidates from four families of chemicals were tested for thermal, chemical and biological stability in reservoir temperature conditions, ranging from 25 °C to 150 °C. Their interaction with three types of rock materials (sandstone, limestone and kaolinite) was also investigated in the same range of temperatures. Results suggest that six of the investigated compounds possess suitable characteristics for use as PITT tracers, while another five compounds may be used to retrieve other information from the reservoir, such as temperature or geochemical data.