Polylactic acid (PLA) is a highly applicable material that is used in 3D printers due to some significant features such as its deformation property and affordable cost. For improvement of the end-use quality, it is of significant importance to enhance the quality of fused filament fabrication (FFF)-printed objects in PLA. The purpose of this investigation was to boost toughness and to reduce the production cost of the FFF-printed tensile test samples with the desired part thickness. To remove the need for numerous and idle printing samples, the response surface method (RSM) was used. Statistical analysis was performed to deal with this concern by considering extruder temperature (ET), infill percentage (IP), and layer thickness (LT) as controlled factors. The artificial intelligence method of artificial neural network (ANN) and ANN-genetic algorithm (ANN-GA) were further developed to estimate the toughness, part thickness, and production-cost-dependent variables. Results were evaluated by correlation coefficient and RMSE values. According to the modeling results, ANN-GA as a hybrid machine learning (ML) technique could enhance the accuracy of modeling by about 7.5, 11.5, and 4.5% for toughness, part thickness, and production cost, respectively, in comparison with those for the single ANN method. On the other hand, the optimization results confirm that the optimized specimen is cost-effective and able to comparatively undergo deformation, which enables the usability of printed PLA objects.

Wind turbines are known to be the most efficient method of green energy production, and wind turbine blades (WTBs) are known as a key component of the wind turbine system, with a major influence on the efficiency of the entire system. Wind turbine blades have a quite manual production process of composite materials, which induces various types of defects in the blade. Blades are susceptible to the damage developed by complex and irregular loading or even catastrophic collapse and are expensive to maintain. Failure or damage to wind turbine blades not only decreases the lifespan, efficiency, and fault diagnosis capability but also increases safety hazards and maintenance costs. Hence, non-destructive testing (NDT) methods providing surface and subsurface information for the blade are indispensable in the maintenance of wind turbines. Damage detection is a critical part of the inspection methods for failure prevention, maintenance planning, and the sustainability of wind turbine operation. Industry 4.0 technologies provide a framework for deploying smart inspection, one of the key requirements for sustainable wind energy production. The wind energy industry is about to undergo a significant revolution due to the integration of the physical and virtual worlds driven by Industry 4.0. This paper aims to highlight the potential of Industry 4.0 to help exploit smart inspections for sustainable wind energy production. This study is also elaborated by damage categorization and a thorough review of the state-of-the-art non-destructive techniques for surface and sub-surface inspection of wind turbine blades.

The field of additive manufacturing (AM) has seen a transformation in the production of intricate and complex parts for various applications. Fused Deposition Modelling (FDM), among AM techniques, has garnered significant attention, particularly in fields like fibre-reinforced composites (FRC). In this study, the world of FDM-printed Polylactic Acid (PLA) components is explored, with a focus on how mechanical properties are influenced by infill percentages and layer widths. Through the utilisation of Response Surface Methodology (RSM), the optimisation of FDM-PLA 3D printing for a wide range of biomaterial applications is achieved, along with the unveiling of the potential for remarkable improvements in mechanical performance. Notably, a remarkable 91% reduction in surface roughness for PLA composites was achieved, accompanied by an impressive 25.6% and 34.1% enhancement in the tensile strength and Young’s modulus of fibre-reinforced PLA composites, respectively. This work, positioned at the crossroads of FDM, lays the groundwork for substantial advancements in the realm of additive manufacturing.

Inspection methods, also known as non-destructive evaluation (NDE), is a process for inspecting materials, products, and facilities to identify flaws, imperfections, and malfunctions without destruction or changing the integrity of materials, structures, and mechanisms. However, detecting those defects requires test conducting and results inferring, which is highly demanding in terms of analysis, performance, and time. New technologies are therefore needed to increase the efficiency, probability of detection, and interpretability of NDE methods to establish smart inspection. In this context, Artificial intelligence (AI), as a fundamental component of the Industry 4.0, is a well-suited tool to address downsides associated with the current NDE methods for analysis and interpretation of inspection results, where methods integrating AI into their inspection process become automated and are known as smart inspection methods. This article sheds a light on the conventional methods and the smart techniques used in defects detection. Subsequently, a comparison between the two notions is presented. Furthermore, it investigates opportunities for the integration of non-destructive evaluation (NDE) methods and Industry 4.0 technologies. In addition, the challenges hindering the progress of the domain are mentioned as the potential solutions. To this end, along with Industry 4.0 technologies, a virtual inspection system has been proposed to deploy smart inspection.

The benefits of laser welding include higher production values, deeper penetration, higher welding speeds, adaptability, and higher power density. These characteristics make laser welding a superior process. Many industries are aware of the benefits of switching to lasers. For example, metal-joining is migrating to modern industrial laser technology due to improved yields, design flexibility, and energy efficiency. However, for an industrial process to be optimized for intelligent manufacturing in the era of Industry 4.0, it must be captured online using high-quality data. Laser welding of aluminum alloys presents a daunting challenge, mainly because aluminum is a less reliable material for welding than other commercial metals such as steel, primarily because of its physical properties: high thermal conductivity, high reflectivity, and low viscosity. The welding plates were fixed by a special welding fixture, to validate alignments and improve measurement accuracy, and a Computer-Aided Inspection (CAI) using 3D scanning was adopted. Certain literature has suggested real-time monitoring of intelligent techniques as a solution to the critical problems associated with aluminum laser welding. Real-time monitoring technologies are essential to improving welding efficiency and guaranteeing product quality. This paper critically reviews the research findings and advances for real-time monitoring of laser welding during the last 10 years. In the present work, a specific methodology originating from process monitoring using Computer-Aided Inspection in laser-welded blanks is reviewed as a candidate technology for a digital twin. Moreover, a novel digital model based on CAI and cloud manufacturing is proposed.

This paper explores the 3D printing of poly vinyl alcohol (PVA) using the fused deposition modeling (FDM) process by conducting statistical modeling and optimization. This study focuses on varying the infill percentage (10–50%) and patterns (Cubic, Gyroid, tri-hexagon and triangle, Grid) as input parameters for the response surface methodology (DOE) while measuring modulus, elongation at break, and weight as experimental responses. To determine the optimal parameters, a regression equation analysis was conducted to identify the most significant parameters. The results indicate that both input parameters significantly impact the output responses. The Design Expert software was utilized to create surface and residual plots, and the interaction between the two input parameters shows that increasing the infill percentage (IP) leads to printing heavier samples, while the patterns do not affect the weight of the parts due to close printing structures. On the contrary, the discrepancy between the predicted and actual responses for the optimal samples is below 15%. This level of error is deemed acceptable for the DOE experiments.