We demonstrate a high power InP-based quantum cascade laser (QCL) (λ ∼ 9 µm) with high characteristic temperature grown by metalorganic chemical vapor deposition (MOCVD) in this article. A 4-mm-long cavity length, 10.5-µm-wide ridge QCL with high-reflection (HR) coating demonstrates a maximum pulsed peak power of 1.55 W and continuous-wave (CW) output power of 1.02W at 293 K. The pulsed threshold current density of the device is as low as 1.52 kA/cm2. The active region adopted a dual-upper-state (DAU) and multiple-lower-state (MS) design and it shows a wide electroluminescence (EL) spectrum with 466 cm−1 wide full-width at half maximum (FWHM). In addition, the device performance is insensitive to the temperature change since the threshold-current characteristic temperature coefficient, T0, is as high as 228 K, and slope-efficiency characteristic temperature coefficient, T1, is as high as 680 K, over the heatsink-temperature range of 293 K to 353 K.
We demonstrate a long-wavelength infrared quantum cascade detector (QCD) that operates at a wavelength of 10 μm, in which the active diagonal transition for the electrons occurs from a fundamental energy level into a miniband in adjacent coupled quantum wells. When compared with a bound-to-bound diagonal transition-based QCD, the use of a miniband as the final transition state increases the absorption strength and enhances the electron extraction efficiency of the device, leading to QCD responsivities of 75 at 180 and 30 mA/W at 300 K for 10.55 μm wavelength operation.
In this article, we report a high-performance λ ~ 4.6 μm quantum cascade laser grown by metal-organic chemical vapor deposition. Continuous wave power of 3 W was obtained from an 8 mm-long and 7.5 μm wide coated laser at 285 K. The maximum pulsed and CW wall-plug efficiency reached 15.4% and 10.4%, respectively. The device performance shows the great potential of metal-organic chemical vapor deposition growth for quantum cascade material and devices.
The band offsets of non-polar A-plane GaN/AlN and AlN/GaN heterojunctions are measured by X-ray photoemission spectroscopy. A large forward-backward asymmetry is observed in the non-polar GaN/AlN and AlN/GaN heterojunctions. The valence-band offsets in the non-polar A-plane GaN/AlN and AlN/GaN heterojunctions are determined to be 1.33 ± 0.16 and 0.73 ± 0.16 eV, respectively. The large valence-band offset difference of 0.6 eV between the non-polar GaN/AlN and AlN/GaN heterojunctions is considered to be due to piezoelectric strain effect in the non-polar heterojunction overlayers.
Increasing the power of a quantum cascade laser by widening laser ridges will lead to the degradation of the beam quality because of the operation of high-order transverse modes. We report on a phase-locked array scheme of terahertz quantum cascade laser (THz QCL) utilizing Talbot effect. By adjusting the absorbing boundary width of each ridge in the array, stable operation of the fundamental supermode is realized. A five-element array shows 4 times power amplification than that of a single ridge device. Due to the large power amplification efficiency, stable mode selection, and simple fabricating process, the phase-locked array scheme is very promising to further improve the performance of THz QCL.
InAs/GaSb type II superlattices were grown on (100) GaSb substrates by metalorganic chemical vapor deposition (MOCVD). A plane of mixed As and Sb atoms connecting the InAs and GaSb layers was introduced to compensate the tensile strain created by the InAs layer in the SL. Characterizations of the samples by atomic force microscopy and high-resolution X-ray diffraction demonstrate flat surface morphology and good crystalline quality. The lattice mismatch of approximately 0.18% between the SL and GaSb substrate is small compared to the MOCVD-grown supperlattice samples reported to date in the literature. Considerable optical absorption in 2- to 8-μm infrared region has been realized. PACS: 78.67.Pt; 81.15.Gh; 63.22.Np; 81.05.Ea