Considering the limited driving range and inconvenient energy replenishment way of battery electric vehicle, fuel cell electric vehicles (FC EVs) are taken as a promising way to meet the requirements for long-distance low-carbon driving. However, due to the limitation of FC power ability, a battery is usually adopted as the supplement power source to fill the gap between the requirement of driving and the serviceability of FC. In consequence, energy management is essential and crucial to an efficient power flow to the wheel. In this paper, a self-optimizing power matching strategy is proposed, considering the energy efficiency and battery degradation, via implementing a deep deterministic policy gradient. Based on the proposed strategy, less energy consumption and longer FC and battery life can be expected in FC EV powertrain with optimal hybridization degree.
1
23 August 2024 in Sustainable Energy Technologies and Assessments
As an auxiliary component with the largest energy consumption in the fuel cell power system, the electric air compressor is of great significance to improve the overall efficiency of the system by reducing its power consumption under the premise of meeting the cathode intake demand. In this paper, the flow state of the gas in the flow field of the fuel cell TSEAC (two-stage electric air compressor) is analyzed by simulation, and the accuracy of the simulation results is verified by experiments. Through the research on the gas compression work of the fuel cell TSEAC, it is found that the higher temperature rise of the gas during the compression process will increase the compression work, thereby reducing the efficiency of the fuel cell TSEAC. Therefore, based on the field synergy theory, this paper designs the heat dissipation structure of the TSEAC elbow. In the common working conditions of fuel cell TSEAC, micro-fin tube is an effective energy-saving structure that takes into account heat dissipation enhancement and flow resistance, and its ratio of micro-fin height to laminar bottom layer thickness ε/δ = 1.6 has the best energy-saving effect. Finally, the energy-saving effect of the micro-fin tube is verified by simulation. The load torque of the optimized fuel cell TSEAC is reduced from 1.540 N·m to 1.509 N·m, and the shaft power is reduced from 14.51 kW to 14.22 kW. Its efficiency increased by 1.9%.
With the increasing power of fuel cells, ultra-high-speed electric air compressors (UHSEACs) have been widely used. However, due to the ultra-high speeds involved, UHSEACs face problems such as long speed adjustment times and large speed fluctuations. Compared to other control methods, Active Disturbance Rejection Control (ADRC) is well-suited for highly nonlinear systems like UHSEACs. The Extended State Observer (ESO), a key component of the ADRC, struggles to accurately observe high-frequency excitations. To address this, the first step is to add a cascaded structure to the ESO and design a Current State Extended State Observer (CS-ESO) to better observe the electromagnetic and load excitations in the UHSEAC. The second step involves designing the ADRC based on the CS-ESO and performing speed adjustment simulations. The third step is to build a UHSEAC experimental platform and a conduct speed adjustment experiment. The findings indicate that, compared to the Proportional Integral Derivative (PID) control, the ADRC with the ESO, and the Sliding Mode Control (SMC), the use of the ADRC with the CS-ESO results in a significant reduction in overshoot—by at least 760 RPM under load-increasing conditions and 140 RPM under load-reducing conditions. Furthermore, the speed regulation time is notably decreased by at least 0.2 s and 0.1 s under these respective conditions.
1 January 2026 in IEEE Transactions on Intelligent Transportation Systems
Predicting voltage degradation at a fixed operating load from proton exchange membrane fuel cells (PEMFCs) subjected to dynamic load cycling is important for durability assessment and maintenance scheduling. This study develops a hierarchical residual forecasting scheme that combines exponential smoothing (ETS), autoregressive integrated moving average (ARIMA), and iTransformer. For every repeated load cycle, the voltage measured at the same predefined load plateau and within-cycle phase is extracted to form a condition-consistent degradation sequence. Pearson-correlation screening retains four synchronous operating variables. ETS first estimates the slowly changing degradation path, ARIMA represents the autocorrelated component of the first residual, and iTransformer forecasts the nonlinear secondary residual with the selected operating information. The three forecasts are then added to obtain the final voltage estimate. The framework is evaluated using a 1000 h dynamic durability dataset from a single PEMFC. Over the held-out interval from 720 to 1000 h, rolling one-step-ahead forecasts yield an RMSE of 1.51 mV, an MAE of 1.12 mV, and an R2 of 0.9759. Relative to the ablated configurations and the compared deep-learning models, the framework follows recovery behavior and nonstationary fluctuations more closely and produces a tighter absolute-error distribution.