Lead-free electroceramics represent an emerging area of research that has the potential to enable new green advances in electronics. Research has mainly focused on the development of new piezoelectric materials for replacing lead containing oxides exhibiting superior electromechanical behavior. Lead-free BiFeO3-based materials are not only the promising candidates to replace lead-based materials but also show intriguing properties which may inspire innovative material design for the next generation of lead-free piezoceramics. This review aims to highlight the current state of research and overlooked aspects in lead-free BiFeO3-based ceramics, which could be insightful in elucidating certain controversial issues. Current strategies to reduce high conductivity, influence of chemical heterogeneity on both functional properties and crystal structure, effective heat treatment procedures, and the role of pseudo-cubic structures on the enhancement of piezoelectric properties are subjects of highlighted within this review as they have a significant impact on the quality of BiFeO3-based lead-free piezoelectrics (but are often disregarded).
17 July 2023 in Japanese Journal of Applied Physics
Rhombohedral Bi(Mg0.5Ti0.5)O3-modified BiFeO3-BaTiO3 ceramics were successfully textured along the nonpolar 〈100〉 direction using the templated grain growth process for the first time. The textured 0.90(0.33BaTiO30.67BiFeO3)0.10Bi(Mg0.5Ti0.5)O3 (33BTBF-10BMT) ceramics were fabricated by a 33BTBF-10BMT matrix with BT templates. The degree of orientation was investigated by various sintering temperatures, and the 80% oriented 33BTBF-10BMT along the 〈100〉 direction was achieved at a relatively high sintering temperature. However, the degree of orientation abruptly decreased at the highest sintering temperature of 1100 °C due to the large pores and low relative density. Based on the analysis of the unipolar strain measurements, the highest strain and d33* values were observed in the textured ceramics with 80% orientation. These textured ceramics exhibited approximately 0.3% strain and a d33* exceeding 400 pm V−1, representing approximately 1.5 times higher values compared to the nontextured ceramics.
1 August 2024 in Japanese Journal of Applied Physics
The significance of increased domain nucleation sites from smaller grain size (GS) of barium titanate (BT) ceramics on piezoelectric properties was analyzed for different types of poling, including conventional DC poling, modified DC poling, and AC plus DC poling, conducted at different poling temperatures. The AC plus DC poling conducted at 1.5 °C above the Curie temperature (TC) showed the highest piezoelectric constant (d33) of 528 pC/N, with an average domain size of 100 nm observed after poling. The d33 improvement was attributed to smaller domain size formation from field-induced phase transitions and homogenous distribution of point defects achieved by the AC field. Comparative analysis with larger grain BT ceramics under AC plus DC poling suggests that defects and volume fraction of grain boundaries in BT ceramics could have an effect on domain sizes.
In lead-free (Bi0.5Na0.5)TiO3–BaTiO3 (BNT–BT) ceramics, the BNT-rich side has R3c ferroelectric domains at room temperature, and modulated P4bm tetragonal nanodomains develop within the R3c rhombohedral phase at approximately the depolarization temperature Td. Such structural phase transitions have conventionally been modulated by doping with additives or by controlling the composition. However, it is considered that the coexistence region between the R3c and P4bm phases is important for enhancing the energy storage behavior because the phase reversal between them, caused by the electric field, can cause the BNT-based ceramics to exhibit an antiferroelectric-like pinched hysteresis loop. In this study, the structural phase transition of BNT–BT ceramics is promoted through process control, that is, by adjusting the cooling rate, and then the stabilization of the P4bm phase and the expansion of the coexistence region of the R3c and P4bm phases were examined, which results in enhanced energy storage behavior. Consequently, BNT–BT ceramics prepared at a slower cooling rate (0.01 °C s−1) than that of normal firing (0.05 °C s−1) demonstrate the stabilization of the P4bm phase and expansion of the coexistence region of the R3c and P4bm phases. Therefore, process control modulates the structural phase transition, which can cause enhanced energy storage behavior.