Lead-free piezoelectric bismuth sodium titanate (Bi0.5Na0.5)TiO3 (BNT) ceramics were prepared by quenching and the correlation among a depolarization temperature Td, the mechanical strength, and their piezoelectric properties were investigated. We controlled the quenching rate in the temperature range from 1100°C to 800°C. We examined the 5 patterns of the quenching rate (QR): 0.05 (ordinary firing, OF), 3.85, 5.77, 6.67, and 15.0 (quenching) oC/s. Td of the rapid quenched sample reached 229°C (QR = 15.0), but its mechanical strength decreased to a quarter of that of the OF ceramics. On the other hand, Td was 211°C at QR = 3.85 which was higher than that of OF-ceramic (QR = 0.05) at about 180°C. Moreover, three-point bending strength (227 MPa) of the quenched BNLT4 (QR = 3.85) was equivalent to that of the OF ceramics (235 MPa). Therefore, both Td and the mechanical strength were improved by controlling the quenching rate.
11 August 2020 in Japanese Journal of Applied Physics
Lead-free ferroelectric and piezoelectric ceramics, (Bi 0.5 Na 0.5 )TiO 3 (BNT), with Mn dopants were prepared by a quenching procedure after sintering to examine the depolarization temperature Td , and then their electrical properties were investigated. The Td of quenched BNT + x Mn (Mn x ) decreased with Mn doping. Also, the Td of quenched Mn x was ∼60 °C higher than that of ordinary firing (OF) samples. Furthermore, the difference of Td (Δ Td ) between the OF and the quenched process increased with increasing of the Mn-substituted amount. The electromechanical coupling factors k33 of Mn x exhibited the same value after quenching. The coercive electric field Ec was increased from 62 to 95 kV cm −1 with increasing of Mn-substituted amount. Thus, the quenching procedure is an effective way of elevating the Td of Mn-doped BNT-based solid solution systems.
Lead-free piezoelectric ceramics based on 0.90(Bi0.5Na0.5)TiO3 – 0.04(Bi0.5Li0.5)TiO3 – 0.06BaTiO3 with additives MnCO3 (0.1 wt%) [BNLBT4-6 + Mn0.1], which have a morphotropic phase boundary composition, were prepared by controlling the quenching rate (QR) and, their high-power piezoelectric and electrical properties were examined. The depolarization temperature Td could be increased by controlling the QR. The Td with QR = 15.0 and 0.05 °C/s was 166 and 119 °C, respectively. Thus, Td was increased by about ∼40 °C due to the quenching effect. Moreover, vibration velocities (v0−p) were observed at 1.3 m/s even after quenching. Additionally, the values of d31, ɛ33T/ɛ0, and s11E decreased, whereas Qm increased after quenching. The quenching effect promoted the dielectric and elastic hardening of BNLBT4-6 + Mn0.1 ceramics. After quenching, Td increased, and the value of d31 × Qm maintained the same value as for ordinary firing (OF) with QR = 0.05. Consequently, quenching was found to be effective for increasing the Td and Qm, hence, a promising effect for high-power piezoelectric applications.
14 September 2022 in Japanese Journal of Applied Physics
Lead-free ferroelectric and piezoelectric ceramics, (Bi 0.5 Na 0.5 )TiO 3 [BNT] ceramics were prepared by controlling the quenching rate. The quenching effects mainly caused an increase in lattice distortion 90- α and Td , contribution of electrical properties and ordered structural phase transitions. In this study, we analyzed oxygen tracer diffusion and examined domain structures for quenched BNT ceramics, and then we proposed a mechanism for the quenching effect. As a result, the diffusion coefficients D of 18 O tracer for the OF and quenched samples were 2.5 × 10 –11 and 1.8 × 10 –11 cm 2 s −1 , respectively, and there were no significant differences in oxygen vacancies after quenching. The correlation between the quenching effect and oxygen vacancies was also examined in BNT with hard and soft dopants. However, the contribution of oxygen vacancies was small thus, the correlation between the quench effect and oxygen vacancies was low. On the other hand, the domain structure of BNT ceramics was observed and the domain size of OF-BNT was around 20 nm. This is a typical domain size for BNT ceramics. In contrast, the domain size of the quenched BNT was 40 nm. Thus, quenching increased the domain size and decreased their density. Consequently, we propose that the domain structure is strongly correlated with the quench-induced increase in lattice distortion and Td , its contribution to electrical properties, and ordered structural phase transitions.
In lead-free (Bi0.5Na0.5)TiO3–BaTiO3 (BNT–BT) ceramics, the BNT-rich side has R3c ferroelectric domains at room temperature, and modulated P4bm tetragonal nanodomains develop within the R3c rhombohedral phase at approximately the depolarization temperature Td. Such structural phase transitions have conventionally been modulated by doping with additives or by controlling the composition. However, it is considered that the coexistence region between the R3c and P4bm phases is important for enhancing the energy storage behavior because the phase reversal between them, caused by the electric field, can cause the BNT-based ceramics to exhibit an antiferroelectric-like pinched hysteresis loop. In this study, the structural phase transition of BNT–BT ceramics is promoted through process control, that is, by adjusting the cooling rate, and then the stabilization of the P4bm phase and the expansion of the coexistence region of the R3c and P4bm phases were examined, which results in enhanced energy storage behavior. Consequently, BNT–BT ceramics prepared at a slower cooling rate (0.01 °C s−1) than that of normal firing (0.05 °C s−1) demonstrate the stabilization of the P4bm phase and expansion of the coexistence region of the R3c and P4bm phases. Therefore, process control modulates the structural phase transition, which can cause enhanced energy storage behavior.
1 July 2024 in Journal of the Ceramic Society of Japan
Lead-free ferroelectric and piezoelectric ceramics, (Bi0.5Na0.5)TiO3 [BNT] have a low depolarization temperature Td of ∼180 °C in ordinary fired (OF) process. To solve this problem, we focused on two effects to increase Td: compositing ZnO and the quenching effect. Td is elevated by dipole pinning or increasing of lattice distortion, respectively. In this study, ZnO–BNT ceramics composites with controlled ZnO content (ZnO 100x, 100x = 0, 10, 20, 30, and 40 mol %) were prepared to increase Td. To further increase the Td, their composites were sintered through a quenching process. We examined the elevation of Td and electrical properties of that quenched ZnO–BNT ceramics composites. As a result, the Td of OF-ZnO100x increased by about 20 °C with increasing the compositing ZnO content. However, the Td of quenched ZnO100x increased uniformly to 215 °C, regardless of the compositing ZnO content. This indicates that quenching is more effective than compositing ZnO in elevation of Td. Quenching is the dominant effect that contributes to the overall ZnO–BNT ceramics composites, whereas compositing ZnO is effective in the vicinity of ZnO grains, that is, it is a local and limited effect. Therefore, the Td of the ZnO–BNT ceramics composites could not be further increased by the quenching effect. In other words, dipole pinning and quenching were not synergistically effective.