Photocatalyst overall water splitting is usually restricted by low carrier separation efficiency and a slow surface reaction rate. Cocatalysts provide a satisfactory solution to significantly improve photocatalytic performance. In this review, some recent advances in cocatalysts for photocatalytic overall water splitting are gathered and divided into groups. Firstly, the loading method of the cocatalyst is introduced. Then, the role of the cocatalyst applied for the photocatalytic overall water splitting process is further discussed. Finally, the key challenges and possible research directions of photocatalytic overall water splitting are proposed. This review is expected to promote research on the design of efficient cocatalysts in photocatalytic systems for overall water splitting.

As an energy carrier characterized by its high energy density and eco-friendliness, hydrogen holds a pivotal position in energy transition. This paper elaborates on the scientific foundations and recent progress of photo- and electro-catalytic water splitting, including the corresponding mechanism, material design and optimization, and the economy of hydrogen production. It systematically reviews the research progress in photo(electro)catalytic materials, including oxides, sulfides, nitrides, noble metals, non-noble metal, and some novel photocatalysts and provides an in-depth analysis of strategies for optimizing these materials through material design, component adjustment, and surface modification. In particular, it is pointed out that nanostructure regulation, dimensional engineering, defect introduction, doping, alloying, and surface functionalization can remarkably improve the catalyst performance. The importance of adjusting reaction conditions, such as pH and the addition of sacrificial agents, to boost catalytic efficiency is also discussed, along with a comparison of the cost-effectiveness of different hydrogen production technologies. Despite the significant scientific advancements made in photo(electro)catalytic water splitting technology, this paper also highlights the challenges faced by this field, including the development of more efficient and stable photo(electro)catalysts, the improvement of system energy conversion efficiency, cost reduction, the promotion of technology industrialization, and addressing environmental issues.

SrTiO₃–LaCrO₃ continuous solid solutions with LaCrO₃ content ranging from 0.00 to 1.00 were prepared via a polymerized complex method. The light absorption ability of SrTiO₃ was improved by the consecutive tuning of the bandgap upon the introduction of LaCrO₃ (up to 570 nm). The solid solutions exhibited significantly enhanced photocatalytic activities for H₂ evolution under visible light irradiation, with an optimized H₂ evolution rate of 1368 μmol h⁻¹ g⁻¹ obtained when LaCrO₃ content was 0.10 (with 1 wt% Pt as cocatalyst), corresponding to an apparent quantum yield of 3.68% at 400 nm. Supported by comprehensive characterization, the improved photocatalytic performance was attributed to the simultaneously adjusted conduction band and valance band originating from the hybridization of Cr 3d, Ti 3d and O 2p orbitals, as well as the accelerated separation and migration of photogenerated charge carriers derived from the distortion of TiO₆ octahedra.

Compound parabolic concentrator (CPC) photocatalytic reactors are commonly used for photocatalytic water splitting in hydrogen production. This study aimed to gain a better understanding of the physical processes in CPC photocatalytic reactors and provide theoretical support for their design, optimization, and operation. The analysis involved the ray tracing approach, Euler–Euler two-fluid model, and discrete ordinates method (DOM) to study solar radiation transfer and particle flow in the reactor. The distribution of solar radiation on the receiving tube’s surface after CPC concentration was obtained by conducting the ray tracing approach. This solar radiation distribution was then coupled into the Euler–Euler two-fluid model to solve for the natural convection flow field, the temperature field, and particle phase volume fraction distribution inside the receiving tube over a period of 120 s. Lastly, the discrete ordinates method (DOM) was used to analyze the transfer of radiation inside the receiving tube at different times, obtaining the distribution of local volume radiative power absorption (LVRPA) and the total radiative power absorption (TRPA) inside the tube. The results showed that the TRPA reached its maximum at 120 s, accounting for 66.61% of the incident solar UV radiation. According to the above results, it could be suggested that adopting an intermittent operation mode in CPC photocatalytic reactors is reasonable and efficient.

Photo(electro)catalysis is regarded as one of the most promising approaches to addressing energy and environmental issues and thus achieving the sustainable development of human society; as such, various catalytic materials have been developed in recent decades