Séverine Gomès

Dr. Séverine Gomès

CNRS, INSA Lyon, CETHIL, Univ. Lyon, UMR5008, 69621 Villeurbanne, France

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 March 2015 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
SGSéverine Gomès
Séverine Gomès
AAAli Assy
Ali Assy
PCPierre-Olivier Chapuis
Pierre-Olivier Chapuis

29 June 2007 in Journal of Physics D: Applied Physics
Verified
Journal Article
Closed access
PDF file
LDL David
L David
SGSéverine Gomès
Séverine Gomès
MRM Raynaud
M Raynaud
The thermal investigation of matter by use of a very localized heat source, scanning thermal microscopy (SThM), permits materials to be probed at the level of very small subsurface volumes. Therefore, the technique appears to be a promising method to study the thermal properties of thin films of submicrometric thickness. In order to estimate this possibility, we propose a new prediction modelling of the measurement with a SThM based on a hot anemometer wire probe used in a dc regime. From this modelling, a study of the sensitivity of measurement to various parameters operating in the thermal interaction between the probe and a mono-layered sample is presented. It gives new data allowing a better understanding of measurements. A new method to calibrate the technique for thermal conductivity measurement with more accuracy is deduced from this study. New data about the different physical mechanisms governing the probe–sample thermal interaction are given. The proposed approach also supplies a method for the determination of the depth resolution of a thermal probe. This last parameter is essential in the framework of thin film study with a given probe. Its dependence on sample thermal conductivity and thermal coupling area are discussed. Our results specify the possibilities of the technique and should contribute to a more accurate determination of thin film thermal conductivity in its dc regime.

7 November 2006
Verified
Book Chapter
Closed access
PDF file
BCBernard Cretin
Bernard Cretin
SGSéverine Gomès
Séverine Gomès
NTNathalie Trannoy
Nathalie Trannoy
PVPascal Vairac
Pascal Vairac

15 December 2020 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
EGE. Guen
E. Guen
PCP.-O. Chapuis
P.-O. Chapuis
RRR. Rajkumar
R. Rajkumar
PDP. S. Dobson
P. S. Dobson
GMG. Mills
G. Mills
SGSéverine Gomès
Séverine Gomès
We propose an approach for the characterization of scanning thermal microscopy (SThM) probe response using a sample with silicon dioxide steps. The chessboard-like sample provides a series of nine surfaces made of the same material, with identical roughness, but consisting of different thicknesses of silica layers standing on a single silicon wafer. The nine regions have different effective thermal conductivities, allowing the calibration of SThM probes within a given set of surface conditions. A key benefit is the possibility of comparing the spatial resolution and the sensitivity to vertical inhomogeneities of the sample for different probes. A model is provided to determine the thermal contact area and contact thermal resistance from the experimental data. The results underline that ballistic heat conduction can be significant in crystalline substrates below the top thin films, especially for film thicknesses lower than 200 nm and effective thermal contact radius lower than 200 nm. They also highlight the sensitivity of SThM to ultrathin films, as well as the substrate below micrometric films under in-air conditions but not when in vacuum. This work advances quantitative nanometer-scale thermal metrology, where usual photothermal methods are more difficult to implement.

18 October 2021 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
EGEloïse Guen
Eloïse Guen
PCPierre-Olivier Chapuis
Pierre-Olivier Chapuis
NKNupinder Jeet Kaur
Nupinder Jeet Kaur
PKPetr Klapetek
Petr Klapetek
SGSéverine Gomès
Séverine Gomès
The impact of surface roughness on conductive heat transfer across nanoscale contacts is investigated by means of scanning thermal microscopy. Silicon surfaces with the out-of-plane rms roughness of ∼0, 0.5, 4, 7, and 11 nm are scanned both under air and vacuum conditions. Three types of resistive SThM probes spanning curvature radii over orders of magnitude are used. A correlation between thermal conductance and adhesion force is highlighted. In comparison with a flat surface, the contact thermal conductance can decrease as much as 90% for a microprobe and by about 50% for probes with a curvature radius lower than 50 nm. The effects of multi-contact and ballistic heat conduction are discussed. Limits of contact techniques for thermal conductivity characterization are also discussed.

1 November 2019 in Review of Scientific Instruments
Verified
Journal Article
Closed access
TNT. P. Nguyen
T. P. Nguyen
LTL. Thiery
L. Thiery
SESébastien Euphrasie
Sébastien Euphrasie
SGSéverine Gomès
Séverine Gomès
BHBruno Hay
Bruno Hay
PVP. Vairac
P. Vairac
We present a procedure dedicated to the calibration of a scanning thermal microscopy probe operated in an active mode and a modulated regime especially for the measurement of solid material thermal conductivities. The probe used is a microthermocouple wire mounted on a quartz tuning fork. Measurements on reference samples are performed successively in vacuum and ambient air conditions revealing a clear difference in the dependence of the thermal interaction between the probe and the sample on the sample properties. Analytical modeling based on the resolution of the heat equation in the wire probe and a description of the thermal interaction using a network of thermal conductances are used to fit experimental data and analyze this difference. We have experimentally verified that the effective thermal contact radius of the probe tip depends on the sample thermal conductivity in ambient conditions, whereas it remains constant in vacuum. We have defined the measurement range of the technique based on the decrease in the probe sensitivity at high thermal conductivities. Considering the experimental noise of our electrical device, it is shown that the maximum measurable value of thermal conductivity is near 23 W m−1 K−1 in vacuum and 37 W m−1 K−1 in ambient air conditions. Moreover, the lowest uncertainties are obtained for thermal conductivities below 5 W m−1 K−1 typically.