Haoxuan Zhang

Mr. Haoxuan Zhang


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
HLHongfu Li
Hongfu Li
HZHaoxuan Zhang
Haoxuan Zhang
GYGuangquan Yue
Guangquan Yue
BGBoyu Guo
Boyu Guo
Ying WuYing Wu
Ying Wu
The investigation of the in-plane shear behavior of prepreg is crucial for understanding the generation of wrinkles of preforms in advanced composite manufacturing processes, such as automated fiber placement and thermoforming. Despite this significance, there is currently no standardized test method for characterizing uncured unidirectional (UD) prepreg. This paper introduces a ±45° off-axis tensile test designed to assess the in-plane shear behavior of UD carbon fiber-reinforced epoxy prepreg (CF/epoxy). Digital image correlation (DIC) was employed to quantitatively track the strains in three dimensions and the shear angle evolution during the stretching process. The influences of the temperature and stretching rate on the in-plane shear behavior of the prepreg were further investigated. The results reveal that four shear characteristic zones and wrinkling behaviors are clearly distinguished. The actual in-plane shear angle is significantly lower than the theoretical value due to fiber constraints from both the in-plane and out-of-plane aspects. When the off-axis tensile displacement (d) is less than 15.6 mm, the ±45° specimens primarily exhibit macroscale in-plane shear behavior, induced by interlaminar interface shear between the +45° ply and −45° ply at the mesoscale. The shear angle increases linearly with the d. However, when d > 15.6 mm, fiber squeezing and wrinkling begin to occur. When d > 29 mm, the in-plane shear disappears in the completely sheared zone (A). The reduction in the resin viscosity of the CF/epoxy prepreg caused by increased temperature is identified as the primary factor in lowering the in-plane shear force resistance, followed by the effect of the increasing resin curing degree. Higher shear rates can lead to a substantial increase in shear forces, eventually causing cracking failure in the prepreg. The findings demonstrate the feasibility of the test method for predicting and extracting uncured prepreg in-plane shear behaviors and the strain-rate and temperature dependency of the material response.

15 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
HZHaoxuan Zhang
Haoxuan Zhang
JLJintong Liu
Jintong Liu
CZCongfa Zhang
Congfa Zhang
HLHongfu Li
Hongfu Li
GYGuangquan Yue
Guangquan Yue
BHBoyan He
Boyan He
Wrinkles are urgent problems to be solved in the process of hot diaphragm preforming. Inter-ply slipping resistance is one of the causes of wrinkles. In this paper, based on the vertical inter-ply slipping test system, the inter-ply slipping behaviors of carbon fiber-reinforced epoxy resin composite prepregs were characterized. The mechanism of wrinkles caused by inter-ply slipping resistance was analyzed. According to the different characteristics expressed by the fiber and resin during the slip process, the inter-ply slipping behaviors of the prepregs were divided into three stages. The effect of temperature on the inter-ply slipping stresses was shown. The temperature will affect the viscosity of the prepregs. When the viscosity of the prepregs is low, the inter-ply slipping resistance will decrease. Based on the Coulomb friction law and the hydrodynamic equation, the inter-ply slipping kinetic equation of the prepregs was established. The inter-ply slipping kinetic equation was introduced into the ABAQUS main program by the ‘vfriction’ subroutine. The introduction of inter-ply slipping dynamics improved the accuracy of predicting the shape and position of wrinkles.