In comparison with tetragonal retaining structures, circular retaining structures have an advantage in terms of controlling the deformation caused by foundation excavation, and are a reasonable choice in engineering practice. Many results have been obtained regarding the effect of tetragonal excavation on the deformation of an adjacent tunnel. Nevertheless, a sufficient understanding of the circular excavation’s effect on the deformation of an adjacent tunnel is currently lacking. Therefore, this study focused on the problem of precise predicting tunnel deformation below a circular excavation. A numerical model was established to calculate the tunnel deformation caused by the circular excavation. An advanced nonlinear constitutive model, known as a hypoplasticity model, which can capture path-dependent and strain-dependent soil stiffness even at small strains, was adopted. The models and their associated parameters were calibrated by centrifuge test results reported in the literature. The deformation mechanism was revealed, and the calculated results were compared with those obtained with a square excavation and the same excavation amount. The differences between the deformations caused by these two types of excavation shapes were analyzed. It was found that under equal excavation area conditions, the excavation-induced deformations of the metro tunnel below a circular excavation were approximately 1.18–1.22 times greater than those below a square excavation. The maximum tunnel tensile bending strain caused by the circular excavation was 32% smaller than that caused by the square excavation. By comparing with the measured results, it is proved that the proposed numerical method can provide effective reference for engineers to analyze soil-structure problems.

Adjacent geotechnical engineering activities, such as deep excavation, may adversely affect or even damage adjacent tunnels. Ground reinforcement before excavation may be an effective approach to reduce tunnel heave as a result of stress relief. However, there are few quantitative studies on the effect of soil reinforcement on tunnel deformation. Moreover, the reinforcement mechanism of the reinforced soil and the reinforcement depth are not fully understood. In order to investigate the effect of reinforcing the ground on the tunnel response, a finite element analysis was conducted based on a previously reported centrifugal model test with no ground reinforcement. The effect of the Young’s modulus and depth of the reinforced soil on tunnel deformation was analyzed. Soil stresses around the tunnel were also considered to explain the tunnel response. The results revealed that the Young’s modulus of the reinforced soil and the reinforcement depth had a significant impact on tunnel deformation as a result of basement excavation. The tunnel heave in the longitudinal direction decreased by 18% and 27% for modulus of the reinforced soil, five times and ten times higher than that of the non-reinforced soil, respectively. The reinforcement depth was effective with regard to controlling the tunnel heave caused by stress relief. This is because the reinforced soil blocked the stress transfer and thus reduced the tunnel heave caused by excavation unloading. It is expected that this study will be useful with regard to taking effective measures and ensuring the safety and serviceability of existing metro tunnels during adjacent excavation.

When the mountain tunnel projects passing through the complex formation with coal, it happened along with disaster accidents such as gas outburst, gas combustion, and gas explosion. These disasters should seriously threaten the safety and life of the construction personnel and affect the normal operation of the tunnel construction. Ventilation is the most effective means to control gas, fire, dust, heat, and other disasters. To study the effects of different ventilation modes in highway gas tunnels, Fluent software was used to simulate forced ventilation, exhaust ventilation, and mixed ventilation in a high gas tunnel of a highway in Hunan. The distribution law of the airflow velocity and gas concentration of these three ventilation modes were obtained to determine the optimal ventilation system. It was shown that vortex zones of different ranges formed in the tunnel for all three ventilation modes, and the gas concentration was higher in the vortex zone than in other regions. Mixed ventilation of them is superior to the other two modes, showing the best ventilation effect with regard to airflow velocity and gas concentration.

Many researchers have investigated the effect of basement excavation on tunnel deformation. However, the influence of consolidation on the interaction of basement-tunnel-soil is rarely considered or systematically studied in clay. In this study, three-dimensional coupled-consolidation finite element analyses were conducted to investigate the effect of consolidation on the tunnel response to excavation. An advanced nonlinear constitutive model was adopted, and numerical parametric investigations were conducted to study the effect of the excavation depth, tunnel stiffness, soil permeability coefficient, and consolidation time on the tunnel response. The results revealed that the basement excavation led to stress release, which caused tunnel heave. Owing to the dissipation of excess negative pore water pressure, the tunnel heave further increased to become approximately twice as large compared with that observed when the foundation pit excavation had just been completed. As the consolidation time increased, the longitudinal tunnel heave and tunnel diameter change caused by the foundation pit excavation gradually increased, but the growth rate was slower down. When the consolidation time changed from 50 days to 150 days, the maximum tunnel heave at the crown and the maximum tunnel diameter change increased by 1.18 and 1.48 times, respectively. The soil’s permeability coefficient did not have a significant effect on the tunnel heave at the crown nor on the tunnel diameter change. The results obtained by this study are expected to be useful as an engineering reference for the analysis of soil structure problems in clay.

Water inrush is a common geological disaster during the roadway excavation process in the broken zone of water‐rich faults. In this paper, the 15107 mining roadway built by Yuxing coal mine in such a fault zone was used as a case study to determine the water content of the surrounding rocks and a fault zone using the transient electromagnetic method (TEM). Also, the mechanics characteristics of such rocks in both saturated and unsaturated states were analyzed, a computational model for fluid‐solid coupling in the water‐rich fault fracture zone was established, and the permeability coefficient of the rocks under both shield support and bolt‐grouting support was compared, along with analyzing the changes in pore pressure, fissure water velocity, and characteristics of deformation in the surrounding rocks. The numerical simulation results show that the fault range has an influence of about 20 m, which causes the forms of permeability coefficient to change like a hump. The permeability coefficient in the fractured zone is the largest, and the mutation rate at the fault plane is faster. Bolting not only reduces the permeability coefficient of the surrounding rock that is 1/10 of the beam support but also prevents the roof fissure water inrushing the roadway and the surrounding rock of the floor, while also causing the pore‐water pressure to decrease, even reduce to zero, in front of the working face and floor. The flow velocity of the fissure water can be decreased by bolting, which can effectively control the deformation of the surrounding rock by 38.7%∼65% compared with the shield support. The practice results show that this method can effectively recover the cracks surrounding the mining roadway and stop gushing water. Concurrently, it successfully controls deformation of the surrounding rocks in the fault zone, thus ensuring stability of the roadway and facilitating safer mining production.