Surface characterization is important and has many applications in the paper industry. Surface characterization requires both surface roughness and surface friction. The relationship between the two has not been fully established for paper and paperboard. It has been a common practice that only the average property and the standard deviation with the coefficient of variation (COV) are reported for surface roughness and friction measurements. This practice, however, provides few information on surface structure and can lead to wrong judgments because two samples having the same average and the COV can have different physical properties. To avoid such mistake, a new surface characterization method has been developed. To this end, surface roughness- and friction-profiles have been obtained using a latest version of Kawabata surface tester (Model: KES-SESRU, Kato Tech, Kyoto Japan). This new version uses the same stylus for both measuring surface roughness and friction under the same operating conditions. It was found that a correlation between the surface roughness and surface friction was very low. This indicates that they should be independent of each other. Therefore, both should be determined for surface characterization.
12 December 2018 in Nordic Pulp & Paper Research Journal
Strength, softness, and absorbency have been identified as the key attributes for disposable consumer products such as tissue, towel and diapers. These attributes are generally evaluated subjectively by users. Although subjective evaluation may be necessary for developing such consumer products, it is time-consuming and expensive. More importantly, it seldom provides guidance or direction regarding process control or product development. The main reason is because subjective evaluation is performed after the fact (ex post facto), not before the event (not ex ante). Accordingly, it has been desirable to develop physical test methods to predict in-use performance of a consumer product. In developing physical test methods to link with subjective evaluation, reliable and relevant subjective data is necessary. Developing physical test methods for softness of hygiene paper has been extremely challenging. The objective of this paper is to demonstrate a feasibility of developing physical test methods which can be highly related to subjective evaluation. To this end, it is hypothesized that tissue softness mainly consists of bulk softness and surface softness. It is assumed that the bulk softness should be determined from bulk stiffness which is defined as the slope between the two specified points in a load-elongation curve from tensile testing. It is also assumed that the surface softness should be determined from the surface properties (roughness and friction) from a surface tester (e. g., Model: KES-SESRU. Kato Tech, Japan). It is suggested that the principles used here for developing physical test methods for tissue softness should be also applicable to other physical properties such as strength and absorbency.
23 March 2019 in Nordic Pulp & Paper Research Journal
Chemical additives are used singly or in combination to impart functionality to hygiene paper (suggested). In particular, in the hygiene paper making process, dry strength agent, wet strength agent, softener, and other are widely used. The effects of chemical additives on the softness components were evaluated. In the case of surface softness, there was no change in MMD according to the addition of dry and wet strength agents. The MMD (mean deviation from the average friction of coefficient) was decreased by adding a softener, which is the purpose of its addition to the hygiene paper making process. The softness and wet strength were improved when the wet strength agent was added before the softener. In addition, lotion treatment was applied to the surface of tissue paper. The surface softness component of non-silicone-based lotion was similar or improved, which may overcome the problems of silicon-based lotion.
5 November 2019 in Nordic Pulp & Paper Research Journal
For the mechanical properties of paper, tensile testing has been widely used. Among the tensile properties, the tensile stiffness has been used to determine the softness of low-density paper. The lower tensile stiffness, the greater softness of paper. Because the elastic region may not be clearly defined in a load-elongation curve, it is suggested to use the tensile modulus which is defined as the slope between the two points in the curve. The two points which provide the best correlation with subjective softness evaluation should be selected. Low-density paper has a much lower tensile strength, but much larger elongation at the break. It undergoes a continuous structural change during mechanical testing. The degree of the structural change should depend on tensile conditions such as the sample size, the gauge length, and the rate of elongation. For low-density paper, the tensile modulus and the tensile strength should be independent of each other. The structure efficiency factor (SEF) is defined as a ratio of the tensile strength to the tensile modulus and it may be used a guideline in developing superior low-density paper products.
30 December 2017 in Journal of Korea Technical Association of The Pulp and Paper Industry
Food handling techniques are especially critical in the summer, as the number of food poisoning incidents tends to surge in warm weather. Bacteria that causes food poisoning is generally found in meats, vegetables, etc. A method for preventing the growth of these bacteria involves using antimicrobial agents and other chemicals such as food preservatives and natural compounds. In this study, antibacterial paper was created with antibacterial extracts from green tea that are harmless in the human body, to evaluate the relationship between antimicrobial activity and the extract concentration. The antimicrobial activity of the green tea extract increased when the level of green tea extract content was increased (starting from 10 mg/mL). In particular, the BKP specimens treated with the antimicrobial extract had bacterial growth that was reduced by approximately 15- 20%. In order to investigate the optimum coating condition of carboxymethyl cellulose (CMC) sodium salt with green tea extract, the paper properties were analyzed. The results were that the tensile index and tearing index were increased up to 5% CMC and 3% CMC, respectively, and then decreased. Meanwhile, air permeability decreased with increased CMC-treatment.