The problem of surface processing and microstructure refinement in stainless steels in laser surface processing in the presence of an external magnetic field has been studied experimentally and theoretically. The effect of both alternating and permanent magnetic fields is discussed. The experimental part includes microstructure assessment of a thin stainless plate annealed by a quasi-continuous laser in the presence of an electromagnetic acoustic transducer. Complementary analytical calculus and numerical simulations of complex transport phenomena in the melting zone are performed. Based on the received data, the effect of the electromagnetic field on the molten zone under laser melting conditions is evaluated and quantified. The obtained results are relevant to laser surface hardening and additive manufacturing.
Selective laser melting (SLM) technology has the advantage of quickly producing complex-shaped parts. To achieve good mechanical properties, it's vital to minimize defects that can occur because of high residual porosity if incorrect processing techniques are used. One effective way to prevent defects is by using computer simulations of underlying processes before printing in the industry. This paper presents a reduced-order numerical model of SLM processing that accurately predicts material porosity by focusing on the key mechanisms that affect the melting and consolidation processes. The focus is on the formation of defects and the expected time that is required until the consolidation of a powder bed is completed. Then the elasticity of the SLM processed materials near defects is analyzed. The modeling results for powder consolidation are shown for comparison with experimental data on stainless steel 316L powder during SLM. This information can be further used for proper selection of SLM parameters such as the scanning speed and the power of the laser source.
21 July 2022 in Microgravity Science and Technology
The motion of a solder inside a ceramic tube with an aluminum insert is considered using the phase-field model of multiphase flows. The problem is solved in the non-isothermal formulation, which allows analyzing the two-phase flow dynamics and the kinetics of the contact line driven by wetting. The total time required for the solder to heat up, melt and then move inside the tube is calculated accounting for its position in the insert and action of wetting forces. The melting heat of the solder is taken into account in the system through the introduction of effective heat capacity as a function of temperature. The values of the dimensionless Bond, Rayleigh, Grasgoff and Marangoni numbers are calculated, which made it possible to analyze the contribution of various physical phenomena to the behavior of the system. It was found that the effect of gravity forces on the shape of the upper and lower free surfaces of the melt is not significant because of the small weight of the solder and the small diameter of the tube. The graphs showing the variation in the center of mass of the solder are obtained. The model predicts the solder leakage from the insert in the presence of gravity, while under microgravity this does not happen. The velocity fields, which develop in a liquid solder at the gravity levels of 1g and µg, are analyzed. Under microgravity conditions, the maximum velocities are caused by the movement of the melt due to wetting forces, while in Earth gravity the average velocities are two orders of magnitude higher since convection currents are present near the walls of the tube. A small thermocapillary effect on the average flow velocity was noted as a result of low temperature gradients.
1 January 2023 in Computational Continuum Mechanics
Аддитивное производство изделий из металлических порошков является быстро развивающимся направлением машиностроения, связанным, в первую очередь, с активным применением в производстве 3D-принтеров. Одной из важных характеристик изделий, изготовленных по данной технологии, является прочность, которая напрямую зависит от первичной микроструктуры материала. Морфология структуры изделий, созданных селективным лазерным плавлением (СЛП), имеет дендритно-ячеистый тип. В статье рассматривается задача определения характерного размера дендритов, формирующихся при высокоскоростной кристаллизации на границе бассейна расплава при СЛП порошка нержавеющей стали 316L. Входящими макропараметрами исследуемой системы служат такие, как термодинамические свойства расплава нержавеющей стали, скорость движения лазерного луча, а также угол ориентации хвостовой части бассейна расплава, где располагается основной участок фронта кристаллизации. В основе анализа лежит приближение Иванцова, постулирующее рост кристаллитов параболической формы, которое найдено как приближенное решение осесимметричной задачи тепло- и массопереноса. Математическое моделирование проведено с использованием модели Александрова и Галенко роста двумерного дендрита. Модель описывает устойчивый рост дендрита в двухкомпонентной системе при наличии конвекции в кристаллизующемся расплаве. На основе этой модели авторами предложена методика расчета скорости кристаллизации и диаметра вершины дендрита в зависимости от таких макропараметров, с помощью которых можно управлять процессом и получать изделия с заданными свойствами. Рассчитанные значения характерных размеров структуры сопоставлены с результатами экспериментального исследования методом просвечивающей электронной микроскопии образцов стали 316L, сделанных посредством СЛП.