The ocean thermal energy conversion (OTEC) is a potential substitute for traditional power plants in tropical islands and coastal regions. However, the OTEC power generation cycle has low thermal efficiency and the integrated utilization is imperative, in which an OTEC coupled with seawater desalination is the most attractive option. Membrane distillation (MD) has distinct advantages making itself a competitive process for seawater desalination, especially the feature that the drained warm seawater from the OTEC power plant can be recycled, improving the integrated output of the OTEC system. In this study, an innovative OTEC system coupling a power generation sub-cycle (PGC) and a water production sub-cycle (WPC) was proposed, composed of the upstream organic Rankine cycle and the downstream membrane distillation modules. The mass, energy and exergy balance of the individual equipment, the sub-cycles and the whole system were performed by constructing the corresponding balance models. The thermal dynamic parameters were calculated, and the performance of power generation and water production was predicted. The results showed that by coupling with the MD desalination, the thermal efficiency of the OTEC system can be greatly improved from 2.19% to 25.38% while the exergy efficiency changed little. For a 100 kW OTEC power generation cycle, the water production rate approached 58.874 t/d. In addition, the economic analysis based on the electricity and water sale was carried out, and the profit can be improved by extra water production, especially in the Hawaii and Rainbow Beach by nearly 20%.
The phononic crystals composed of soft materials have received extensive attention owing to the extraordinary behavior when undergoing large deformations, making it possible to provide tunable band gaps actively. However, the inverse designs of them mainly rely on the gradient-driven or gradient-free optimization schemes, which require sensitivity analysis or cause time-consuming, lacking intelligence and flexibility. To this end, a deep learning-based framework composed of a conditional variational autoencoder and multilayer perceptron is proposed to discover the mapping relation from the band gaps to the topology layout applied with prestress. The nonlinear superelastic neo-Hookean model is employed to describe the constitutive characteristics, based on which the band structures are obtained via the transfer matrix method accompanied with Bloch theory. The results show that the proposed data-driven approach can efficiently and rapidly generate multiple candidates applied with predicted prestress. The band gaps are in accord with each other and also consistent with the prescribed targets, verifying the accuracy and flexibility simultaneously. Furthermore, based on the generalization performance, the design space is deeply exploited to obtain desired soft structures whose stop bands are characterized by wider bandwidth, lower location, and enhanced wave attenuation performance.
As a key component connecting a floating wind turbine with static sea cables, dynamic cables undergo significant tensile and bending loads caused by hydrostatic pressure, self-weight, waves, and ocean currents during service, which can lead to fatigue failure. Thus, dynamic and fatigue analyses are necessary for the design and operation of dynamic cables. In this study, a fatigue analysis of the three-core four-layer armored dynamic cable used in a semisubmersible floating wind turbine was carried out at a water depth of 25 m. The Miner linear cumulative damage method, based on material S-N curves, was used to predict fatigue life. The results indicate that, at 10 times the safety factor, the dynamic cables meet the design requirement of a 30-year service life in the studied marine environment. The maximal curvature of the dynamic cable always appears at the exit of the bend stiffener, even beyond the allowed point. Adding weights to the section where the cable exits the bend stiffener and adjusting the bend stiffener’s hanging angle can both reduce the curvature at the bend stiffener exit. The scheme of adjusting the bend stiffener’s hanging angle is preferred, for it is easier for simultaneous adjusting and inducing much smaller extra stress in the cable. As the hanging angle increases, the curvature at the bend stiffener exit decreases, while the maximal effective tension and maximal von Mises stress gradually increase. For certain operating conditions, especially with higher waves, it is better to adjust the hanging angle to avoid excessive curvature and, meanwhile, ensure the increase in the stress within a reasonable range.
In this study, a new type of 2D piezoelectric phononic crystal with a square hollow and convex structures is designed and established. A theoretical study of the piezoelectric phononic crystal is presented in this article to investigate the transmission properties of waves in terms of complex dispersion relations. Based on the finite discretization technique and plane wave expansion, the formula derivation of the real band structure is achieved as well as the complex band diagrams are obtained. The numerical results are presented to demonstrate the multiple broadband complete bandgaps produced by the designed piezoelectric phononic crystal and the propagation characteristics of the elastic waves for different directions. In addition, the transmission loss in the ΓX direction is calculated to verify the band structure. Finally, the effects of the thickness and the square hollow side length on the band structure are discussed.
The safe and efficient design of dynamic submarine cables is critical for the reliability of floating offshore wind turbines, yet traditional time-domain simulation-based optimization approaches are computationally intensive and time consuming. To address this challenge, this study proposes a closed-loop optimization framework that couples machine learning with intelligent optimization algorithms for a dynamic cable configuration design. A high-fidelity surrogate model based on a backpropagation (BP) neural network was trained to accurately predict cable dynamic responses. Three optimization algorithms—Particle Swarm Optimization (PSO), Ivy Optimization (IVY), and Tornado Optimization (TOC)—were evaluated for their effectiveness in optimizing the arrangement of buoyancy and weight blocks. The TOC algorithm exhibited superior accuracy and convergence stability. Optimization results show an 18.3% reduction in maximum curvature while maintaining allowable effective tension limits. This approach significantly enhances optimization efficiency and provides a viable strategy for the intelligent design of dynamic cable systems. Future work will incorporate platform motions induced by wind turbine operation and explore multi-objective optimization schemes to further improve cable performance.
8 November 2022 in Mechanics of Advanced Materials and Structures
A hybrid planar micro-lattice made of functionally graded materials is proposed where the active and passive constituents are constructed by functionally graded beams with and without partially distributed piezoelectric attachments respectively. The analytical model for predicting complex band structure is presented via the spectral element method in combination with the modified couple stress theory and power law, whose accuracy is validated by the finite element method. By adjusting size dependence, feedback control gain, material gradient and arrangement of piezo-patches, controllable wave propagation and attenuation is achieved, which further advances the implementation of optimizations to obtain ultra-wide low frequency stop bands.