Jiageng Liu

Dr. Jiageng Liu

orcid

Research Focus & Metrics

Academic Career Length

24Years (2003-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 February 2003 in Acta Crystallographica Section E Crystallographic Communications
Verified
Journal Article
Open access
PDF file
JLJiageng Liu
Jiageng Liu
DXDuan-Jun Xu
Duan-Jun Xu
CHChen-Hsiung Hung
Chen-Hsiung Hung

18 November 2022 in Crystals
Verified
Journal Article
Open access
PDF file
JLJiageng Liu
Jiageng Liu
JWJiang Wu
Jiang Wu
QLQian Liu
Qian Liu
SJShuai Ji
Shuai Ji
XZXinlu Zheng
Xinlu Zheng
JWJiang Wang
Jiang Wang
Ti/Al composite sheets were prepared using the cold rolling process, and different initial aluminium strengths were considered. The results showed that the peel strength of the Ti/Al composite sheet increased with the increasing initial strength of aluminium under the same reduction. A higher strength of the initial aluminium corresponds to better deformation coordination between titanium and aluminium, where the strain hardening of titanium and aluminium plays an important role. The change degree of the components of twins on the titanium side for the Ti/Al composite sheet with a low aluminium strength is stronger than that for the Ti/Al composite sheet with a high aluminium strength. The strong change in the components of twins may result in the low uniformity of the microstructure on the titanium side. The analysis of the peeling surface shows aluminium residue on the titanium side, while there was almost no titanium residue on the aluminium side. At the same reduction, a higher strength of aluminium corresponds to less aluminium residue on the titanium side. The bonding properties of Ti/Al cold-rolled composite sheets were determined by four strong bonding areas. The strength of the initial aluminium was the main factor, and the residual amount of aluminium on the titanium side of the peeling surfaces was a secondary factor.

28 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
JLJiageng Liu
Jiageng Liu
JWJiang Wu
Jiang Wu
QLQian Liu
Qian Liu
SJShuai Ji
Shuai Ji
XZXinlu Zheng
Xinlu Zheng
JWJiang Wang
Jiang Wang
The large difference in mechanical properties and plastic deformation ability of each layer will have a great impact on the overall performance of a composite sheet prepared by cold-roll bonding. The effect of rolling and material variables on the stress distribution and bonding state in the rolling deformation zone should be studied. In this work, an accurate cold-rolling deformation model considering the anisotropic effect and position-dependent friction model is established using the slab method. Effects of different process and material variables are analyzed. Related experiments were performed on Ti-Al clads and calculation results from the deformation model were compared with the experimental results. This model can well predict the Ti/Al thickness ratio after rolling, and the smaller the initial aluminum strength, the more accurate the predicted value; the minimum error is within 1%. The deformation coordination between the titanium and aluminum layers becomes better with the increase in rolling reduction and initial aluminum strength. At 50% reduction, the deformation ratio of titanium and aluminum increases from 93.8% to 98.1%, which is consistent with the trend of the results calculated using this model.

24 December 2024 in Coatings
Verified
Journal Article
Open access
PDF file
WLWanting Lu
Wanting Lu
WDWenhui Deng
Wenhui Deng
ZZZxy Z
Zxy Z
KLKunling Lin
Kunling Lin
MLMengyuan Liu
Mengyuan Liu
JLJiageng Liu
Jiageng Liu
Due to the advantages of high capacity, low working voltage, and low cost, lithium-rich manganese-based material (LMR) is the most promising cathode material for lithium-ion batteries; however, the poor cycling life, poor rate performance, and low initial Coulombic efficiency severely restrict its practical utility. In this work, the precursor Mn2/3Ni1/6Co1/6CO3 was obtained by the continuous co-precipitation method, and on this basis, different doping levels of aluminum–magnesium were applied to modify the electrode materials by high-temperature sintering. The first discharge capacity can reach 295.3 mAh·g−1 for the LMR material of Li1.40(Mn0.666Ni0.162Co0.162Mg0.005Al0.005)O2. The Coulombic efficiency is 83.8%, and the capacity retention rate remains at 84.4% after 300 cycles at a current density of 1 C for the Mg-Al co-doped LMR material, superior to the unmodified sample. The improved electrochemical performance is attributed to the increased oxygen vacancy and enlarged lithium layer spacing after trace magnesium–aluminum co-doping, enhancing the lithium-ion diffusion and effectively mitigating voltage degradation during cycling. Thus, magnesium–aluminum doping modification emerges as a promising method to improve the electrochemical performance of lithium-rich manganese-based cathode materials.

30 March 2025 in Processes
Verified
Journal Article
Open access
PDF file
Feng WangFeng Wang
Feng Wang
WLWenting Liu
Wenting Liu
LLLina Liang
Lina Liang
YLYue Liu
Yue Liu
ZHZhengru Huang
Zhengru Huang
JWJiang Wang
Jiang Wang
The ZrCo hydrogen storage alloy is a relatively good hydrogen isotope carrier applied in the National Thermonuclear Fusion Reactor. However, the intrinsic disproportionation characteristics of ZrCo alloy reduces its cyclic service life and limits its further application. To address this issue, Zr0.8Ti0.2Co alloy is developed and exhibits good anti-disproportionation performance than pure ZrCo. Nevertheless, Zr0.8Ti0.2Co suffers from relatively poor hydrogen absorption kinetics. In this study, the effects of Cr substitution on its microstructure and hydrogen storage performance are investigated. Zr0.8Ti0.2CrxCo1−x (x = 0, 0.05, 0.1, 0.15) samples are composed of the ZrCo main phase. After Cr substitution, the second phases of CoZr2 and TiCr2 Laves phases appear. With the increase in Cr content, the lattice constant and unit cell volume of the Zr0.8Ti0.2Co alloy increase. Meanwhile, the hydrogen absorption incubation time of the Zr0.8Ti0.2Co alloy is shortened, and the activation performance is enhanced, which is attributed to the catalytic effect of the Laves second phases. The enthalpy of hydrogen absorption of the Zr0.8Ti0.2Co alloy increases, and the stability of the hydride is enhanced with increasing Cr addition. Zr0.8Ti0.2Cr0.05Co0.95 demonstrates excellent hydrogen desorption kinetics while maintaining robust anti-disproportionation performance. The element substitution and the composition design are effective approaches to improving the comprehensive hydrogen storage performance of ZrCo-based alloys, which provides guidance for its further application.