Qian Liu

Qian Liu


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 September 2020 in Materials
Verified
Journal Article
Open access
PDF file
JDJialei Dai
Jialei Dai
ZYZixuan Yang
Zixuan Yang
QLQian Liu
Qian Liu
Herein, we investigated the effects of Ce on the corrosion behavior of NdFeB magnets in 3.5% NaCl solutions using electrochemical tests, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) mapping, and scanning Kelvin probe force microscopy (SKPFM). We demonstrated that Ce markedly enhances the corrosion resistance of NdFeB magnets. Ce primarily replaces Nd in the Nd-rich phase instead of matrix phase, increasing the surface potential of the Nd-rich phase. An increase in the Ce content from 0 to 5.21 wt%, decreased the potential difference between the main phase and (Nd, Ce)-rich phase from 350.2 mV to 97.7 mV; therefore, the corrosion resistance of the magnetic materials increased. The corrosion resistance constituted the Nd-rich phase < the void < metal matrix. Moreover, based on the results of the study, we discussed the impact mechanism of additions of Ce on the corrosion resistance of the magnets.

23 November 2020 in Metals
Verified
Journal Article
Open access
PDF file
QLQian Liu
Qian Liu
YTYaqiang Tian
Yaqiang Tian
JZJinpo Zhai
Jinpo Zhai
LTLu Tian
Lu Tian
LCLiansheng Chen
Liansheng Chen
Liqing ChenLiqing Chen
Liqing Chen
High quality products are demanded due to increasingly fierce market competition. In this paper, the generation of surface wrinkle defect of welding wire steel ER70S-6 was studied by the combination of the experimental method and finite element simulation. Firstly, a thermal compression test was conducted on the Gleeble-3500 thermosimulator under different strain rates and temperatures and a strain dependent Arrhenius-type constitutive function was employed to fit the flow stress–strain curves obtained from the experiments. Then, the elastoplastic constitutive relationship was implemented using radial return mapping algorithm by means of the user subroutine VUMAT of Abaqus/Explicit. A new instability criterion was proposed to predict the possibility of the surface wrinkle defect during the multipass hot bar rolling process. In order to verify the reliability of the finite element model of the six-pass continuous rolling process, the simulated results were compared with experimental data. Finally, the effects of groove width and groove radius on the billet were investigated by the orthogonal test method, and the friction coefficient and rolling temperature. The results show that the groove width and groove radius are key factors to suppress the surface wrinkle defect. Decreasing the groove width can be beneficial for improving the surface quality and reducing the fillet radius. The optimized combination of the rolling process parameters was further applied in an industrial test and the surface quality of the billet was greatly improved.

18 November 2022 in Crystals
Verified
Journal Article
Open access
PDF file
JLJiageng Liu
Jiageng Liu
JWJiang Wu
Jiang Wu
QLQian Liu
Qian Liu
SJShuai Ji
Shuai Ji
XZXinlu Zheng
Xinlu Zheng
JWJiang Wang
Jiang Wang
Ti/Al composite sheets were prepared using the cold rolling process, and different initial aluminium strengths were considered. The results showed that the peel strength of the Ti/Al composite sheet increased with the increasing initial strength of aluminium under the same reduction. A higher strength of the initial aluminium corresponds to better deformation coordination between titanium and aluminium, where the strain hardening of titanium and aluminium plays an important role. The change degree of the components of twins on the titanium side for the Ti/Al composite sheet with a low aluminium strength is stronger than that for the Ti/Al composite sheet with a high aluminium strength. The strong change in the components of twins may result in the low uniformity of the microstructure on the titanium side. The analysis of the peeling surface shows aluminium residue on the titanium side, while there was almost no titanium residue on the aluminium side. At the same reduction, a higher strength of aluminium corresponds to less aluminium residue on the titanium side. The bonding properties of Ti/Al cold-rolled composite sheets were determined by four strong bonding areas. The strength of the initial aluminium was the main factor, and the residual amount of aluminium on the titanium side of the peeling surfaces was a secondary factor.

28 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
JLJiageng Liu
Jiageng Liu
JWJiang Wu
Jiang Wu
QLQian Liu
Qian Liu
SJShuai Ji
Shuai Ji
XZXinlu Zheng
Xinlu Zheng
JWJiang Wang
Jiang Wang
The large difference in mechanical properties and plastic deformation ability of each layer will have a great impact on the overall performance of a composite sheet prepared by cold-roll bonding. The effect of rolling and material variables on the stress distribution and bonding state in the rolling deformation zone should be studied. In this work, an accurate cold-rolling deformation model considering the anisotropic effect and position-dependent friction model is established using the slab method. Effects of different process and material variables are analyzed. Related experiments were performed on Ti-Al clads and calculation results from the deformation model were compared with the experimental results. This model can well predict the Ti/Al thickness ratio after rolling, and the smaller the initial aluminum strength, the more accurate the predicted value; the minimum error is within 1%. The deformation coordination between the titanium and aluminum layers becomes better with the increase in rolling reduction and initial aluminum strength. At 50% reduction, the deformation ratio of titanium and aluminum increases from 93.8% to 98.1%, which is consistent with the trend of the results calculated using this model.

28 May 2024 in Crystal Growth & Design
Verified
Journal Article
Closed access
QLQian Liu
Qian Liu
BZBojian Zhou
Bojian Zhou
JLJiageng Liu
Jiageng Liu
SJShaolong Jiang
Shaolong Jiang

11 June 2020 in Applied Physics A
Verified
Journal Article
Closed access
PDF file
QLQian Liu
Qian Liu
YTYaqiang Tian
Yaqiang Tian
XZXiaoping Zheng
Xiaoping Zheng
LCLiansheng Chen
Liansheng Chen
YZYuqing Zhao
Yuqing Zhao
SJShaolong Jiang
Shaolong Jiang