In the quadcopter, the performance of driving motor deteriorates with repeated flying cycles. However, the degradation is compensated by feedback control to maintain intended flight mission, which renders the state of degradation difficult to estimate until the failure occurrence. In order to solve this problem, a novel Kalman filter-based prognostics framework is proposed, which predicts the current health and remaining useful life (RUL) of the driving motors by taking advantage of the flight control data acquired during the flight, not by installing additional sensors. The framework consists of the online health diagnosis by the two-stage Kalman filters to estimate the motor speeds and the maximum thrusts, and the offline failure prognosis to predict the RUL of each motor by the particle filter algorithm. A Parrot Mambo drone is chosen to demonstrate the approach, in which the flight control data are collected during the hovering motion at regular intervals while one of the motors undergoes accelerated degradation. The result shows that the framework predicts the RUL of the degraded motor with close accuracy against the failure threshold which is the minimum thrust for takeoff of the quadcopter.
The advent of the New Space Era has significantly accelerated the development of space equipment systems using commercial off-the-shelf components. Field Programmable Gate Arrays are increasingly favored for their ability to be easily modified, which substantially reduces both development time and costs. However, their high susceptibility to space radiation poses a considerable risk of mission failure, potentially compromising system reliability in harsh space environments. To mitigate this vulnerability, the implementation of fault-tolerant mechanisms is essential. In this study, we applied eight distinct fault-tolerant mechanisms to various circuits and conducted a comparative analysis between two different categories: hardware redundancy and informational redundancy. This comparison was based on consistent criteria, specifically the Architectural Vulnerability Factor and resource consumption. Utilizing statistical fault injection tests and specialized software, we quantitatively measured structural vulnerability, power consumption, delay, and area. The results revealed that while the Hamming Code achieved the lowest structural vulnerability, it resulted in approximately fourfold increases in resource consumption. Conversely, Triple Modular Redundancy provided high reliability with relatively minimal resource usage. This research elucidates the trade-offs between reliability and resource overhead among different fault-tolerant mechanisms, highlighting the critical importance of selecting appropriate mechanisms based on system requirements to optimize the balance between reliability and resource utilization. Our analysis offers new insights essential for optimizing fault-tolerant mechanisms in space applications. Future work should explore more complex circuit architectures and diverse fault models to refine the selection criteria for fault-tolerant mechanisms tailored to real-world space missions.
In the development of safety-critical systems, it is important to perform failure modes and effects analysis (FMEA) to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an automatic FMEA tool that integrates the model-based design (MBD), FMEA, and simulated fault injection techniques in a single environment. The automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool: First, the automatic FMEA tool automatically generates FMEA reports, unlike the traditional spreadsheet-based FMEA tools. Second, the automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the automatic FMEA were compared to those of the legacy FMEA.
In this paper, we propose Automatic Configuration Memory Fault Injection (ACMFI), a tool that calculates the architectural vulnerability factor (AVF) and soft error rate (SER) using the emulation fault injection technique. SER, which is essential for the safety design of aerospace electronics, can be obtained by experiments (beam tests) performed in a beam facility equipped with high-energy radiation facilities. However, SER calculation using beam tests has the disadvantage of a high cost and a long waiting time, making it difficult to use in the conceptual design stage, which is the aerospace system development stage and the initial HW/SW development stage. Using the emulation fault injection method, it is possible to estimate the SER, which can be used in the system safety design phase. This paper describes the ACMFI tool, which automatically performs emulation fault injection in SRAM-based FPGAs, which are widely used in aerospace electronic hardware. Unlike the existing methods, the proposed method has the advantage of minimizing the side effects by injecting faults into a dedicated SRAM area. In other words, the SER obtained by the proposed method can be estimated more accurately than the SER result obtained by the existing method. To prove the accuracy of the proposed test method, the SER calculated by performing an emulation fault injection test on the same FPGA was compared with the SER results tested at the beam facility. The method of obtaining SER using the proposed ACMFI gave results that were closer to the SER obtained by testing at the beam facility than the method of obtaining SER using the existing EMFI. The proposed method is used to calculate the failure rate, which is a key variable in determining the development assurance level when performing safety design tests in aerospace system development, enabling the development of safer systems and lower cost/higher quality aerospace electronic equipment than before.
Advances in deep submicron semiconductor technology have increased the significance of studying soft errors caused by atmospheric radiation in avionics systems. Atmospheric radiation particles, such as protons and neutrons, can induce Single Event Upsets (SEUs) in sensitive electronic components, leading to system malfunctions and data corruption. Traditional reliability analysis based on older IC or LSI components may fail to account for radiation-induced effects. However, modern avionics systems equipped with state-of-the-art VLSI components are increasingly susceptible to Single Event Upsets (SEUs), potentially leading to underestimated failure rates in these advanced systems. This study introduces an integrated failure rate analysis that incorporates both the physics of failure rates resulting from aging and wear-out and soft error rates induced by atmospheric radiation. The proposed failure rate analysis of the reliability of avionics operating at altitudes of up to 18 km by combining the physics of failure rates with radiation-induced failure rates was derived using a semi-empirical SEU estimation method. Case studies using the Zynq 7000 board, sourced from AMD (San Jose, CA, USA), confirmed that the integrated failure rate analysis provides more accurate reliability predictions compared to conventional analysis. This approach is expected to improve the accuracy of safety assessments during the preliminary development stages, leading to a shortened development timeline and enhanced design quality.
In the development of the safety-critical systems, it is important to perform Failure Modes and Effects Analysis (FMEA) process to identify potential failures. However, traditional FMEA activities tend to be considered difficult and time-consuming tasks. To compensate for the difficulty of the FMEA task, various types of tools are used to increase the quality and the effectiveness of the FMEA reports. This paper explains an Automatic FMEA tool which integrates the Model-based Design (MBD), FMEA, and Simulated Fault Injection techniques in a single environment. The Automatic FMEA tool has the following advantages compared to the existing FMEA analysis tool. First, the Automatic FMEA tool automatically generates FMEA reports compared to the traditional spreadsheet-based FMEA tools. Second, the Automatic FMEA tool analyzes the causality between the failure modes and the failure effects by performing model-based fault injection simulation. In order to demonstrate the applicability of the Automatic FMEA, we used the electronic fuel injection system (EFI) Simulink model. The results of the Automatic FMEA were compared to that of the legacy FMEA.