The surface or sheath effect on core-shell nanowires plays an important role in the nanomechanical test. In the past few years, SiC nanowires have been synthesized using various methods with an uneven and uncontrollable amorphous silicon dioxide sheath. The bending Young’s modulus of the SiC nanowires has scarcely been measured, and the effect of the oxide sheath has not been taken into account. In this paper, SiO₂-coated SiC (SiO₂@SiC) nanowires were synthesized using the chemical vapor deposition method, followed by thermal reduction. Scanning electron microscopy and transmission electron microscopy show that the SiO₂@SiC nanowires in this paper have diameters ranging from 130 ~ 150 nm, with the average thickness of SiO₂ layer approximately 14 nm. After different processing times with 1 mol/L NaOH, approximately 5 nm, 9 nm, 14 nm silicon dioxide layers were obtained. The results of the three-point-bending test show that the modulus of SiO₂@SiC nanowires is found to clearly decrease with the increase in oxide thickness and the influence of the oxide sheath should not be ignored when the layer thickness is above 5 nm. Young’s modulus of the SiO₂@SiC nanowires calculated in this study by the core-shell structure model is in good agreement with the theoretical value.

To solve the problem of poor formability of magnesium alloys, the bending and straightening process was used to successfully introduce large-volume $\left\{10\overline{1}2\right\}$ tensile twins and dynamic recrystallization into the plates, and the comprehensive mechanical properties of the plates were improved, in which the anisotropy index (Lankford value: $\overline{r}$) decreased by 77%, and the corresponding Erishen value (IE) increased by 88%. The research shows that most of the continuous dynamic recrystallization (CDRX) and discontinuous dynamic recrystallization (DDRX) inherit the grain orientation of the parent grains, and a few have deviations from the parent grains. The twinning-assisted dynamic recrystallization (TDRX) can effectively inherit the grain orientation of the parent grain and retain the orientation relationship of the $\left\{10\overline{1}2\right\}$ tensile twin. The cooperation of the pre-set tensile twinning and various dynamic recrystallization processes leads to the deflection of the basal plane, which effectively weakens the basal texture and promotes the activation of various non-basal slip systems. Combined with grain refinement strengthening and dislocation strengthening, the magnesium alloy plate, after bending and straightening, obtains good comprehensive mechanical properties.

The conventional rolling of magnesium alloy with a single pass and large reduction will cause severe edge cracking. The sheet without cracks can be achieved by limited width rolling. The microstructure evolution of the sheet with cracks after conventional rolling and the sheet without cracks after limited width rolling is explored, and an effective mechanism for solving edge cracks is proposed. Conventional rolling can fully develop twin evolution due to high deformation, and three stages of twinning evolution can be observed and the secondary twins easily become the nucleation points of micro cracks, resulting in a large number of cracks propagating along the twin lamellae. Cracks terminate at dislocation accumulation because the accumulation of a large number of dislocations can hinder propagation. Dislocation shearing of twins to eliminate the high localization caused by twins and induce the tensile twins to weaken the basal surface texture provides an effective plastic deformation mechanism of crack inhibition, which is useful for expanding the engineering application of magnesium alloy rolled sheets.

Precipitation in super-austenitic stainless steels will significantly affect their corrosion resistance and hot workability. The effects of Cr and Mo on precipitation behaviors were mainly achieved by affecting the driving force for precipitation, especially Mo has a more substantial promotion effect on the formation of the σ phase than Cr. In the present study, B addition to the S31254 super-austenitic stainless steels shows an excellent ability to inhibit precipitation. The effect of B on the precipitation behaviors was investigated by microstructure characterization and theoretical calculations. The experimental observation shows that the small addition of B inhibits the formation of the σ phase along grain boundaries and changes from continuous to intermittent distribution. Moreover, the inhibitory effect increased obviously with the increase of B content. The influence of B addition was theoretically analyzed from the atomic level, and the calculation results demonstrate that B can inhibit the formation of σ phase precipitates by suppressing Mo migration to grain boundaries. It is found that B and Mo are inclined to segregate at Σ5 and Σ9 grain boundaries, with B showing the most severe grain boundary segregation tendency. While B distribution at the grain boundary before precipitation begins, the segregation of Mo and Cr will be restrained. Additionally, B’s occupation will induce a high potential barrier, making it difficult for Mo to diffuse towards grain boundaries.

In order to reduce the segregation of Cr and Mo and inhibit the precipitates, we added a small amount of B and Ce to traditional S31254 steel. Using an air-cooling and low-temperature diffusion treatment, the purpose was to control B and Ce at the grain boundary. The heat-treatment process could prompt co-segregation of B, precipitate-forming elements, and Ce at the grain boundary at 950 °C. After aging at 950 °C for different amounts of time, the diffusion treatment had an obvious inhibitory effect on the precipitates that caused them to become discontinuous, fine, and serrated. The B-containing serrated precipitates were only rich in Mo, while Cr was homogeneously distributed in the probed volume. A uniform distribution of Cr reduced the Cr-depleted zone in the area adjacent to the phase interface. Ce was observed to be segregated at the grain boundary. This showed that Ce could inhibit the formation of precipitates at the grain boundary. The serrated precipitates had an obvious resistance to intergranular corrosion.