With high water cuts and high permeability reservoirs entering the middle and late stage, many old oil fields in China are facing the dilemma of oil and gas resource exhaustion, while low-permeability reservoir resources remain very rich.
In order to solve the problem of gas channeling during CO2 flooding in low-permeability reservoirs, a novel CO2 responsive gel channeling system was prepared by using carrageenan, branched polyethylene imide and ethylenediamine under laboratory conditions. Based on the Box–Behnken response surface design method, the optimal synthesis concentration of the system was 0.5 wt% carrageenan, 2.5 wt% branchized polyethylenimide and 6.5 wt% ethylenediamine. The micromorphology of the system before and after response was characterized by scanning electron microscopy. The rheology and dehydration rate were tested under different conditions. The channeling performance and enhanced oil recovery effect of the gel system were simulated by a core displacement experiment. The experimental results show that the internal structure of the system changes from a disordered, smooth and loosely separated lamellae structure to a more uniform, complete and orderly three-dimensional network structure after exposure to CO2. The viscosity of the system was similar to aqueous solution before contact with CO2 and showed viscoelastic solid properties after contact with CO2. The experiment employing dehydration rates at different temperatures showed that the internal structure of the gel would change at a high temperature, but the gel system had a certain self-healing ability. The results of the displacement experiment show that the plugging rate of the gel system is stable at 85.32% after CO2 contact, and the recovery rate is increased by 17.06%, which provides an important guide for the development of low-permeability reservoirs.
To address the issues of poor thermal stability, inadequate salt tolerance, and environmental risks in conventional gel systems for the development of high-temperature, high-salinity heterogeneous reservoirs, a triple-synergy gel system comprising anionic polyacrylamide (APAM), polyethyleneimine (PEI), and phenolic resin (SMP) was developed in this study. The optimal synthesis parameters—APAM of 180 mg/L, PEI:SMP = 3:1, salinity of 150,000 ppm, and temperature of 110 °C—were determined via response surface methodology, and a time–viscosity model was established. Compared with existing binary systems, the proposed gel exhibited a mass retention rate of 93.48% at 110 °C, a uniform porous structure (pore size of 2–8 μm), and structural stability under high salinity (150,000 ppm). Nuclear magnetic resonance displacement tests showed that the utilization efficiency of crude oil in 0.1–1 μm micropores increased to 21.32%. Parallel dual-core flooding experiments further confirmed the selective plugging capability in heterogeneous systems with a permeability contrast of 10:1: The high-permeability layer (500 mD) achieved a plugging rate of 98.7%, while the recovery factor of the low-permeability layer increased by 13.6%. This gel system provides a green and efficient profile control solution for deep, high-temperature, high-salinity reservoirs.
Foam is a medium-stable system composed of gas and liquid phases, which has the advantages of low density at the gas phase and high viscosity at the liquid phase, and has a wide application in oil and gas field development and mineral flotation, but its special medium-stable system also brings many problems in industry applications. Scientists have carried out extensive analyses and research on the foam stability and bubble-bursting mechanism, which initially clarified the rules of bubble breakage caused by environmental factors such as temperature and pressure, but the mechanism of bubble bursting under the action of internal factors such as liquid mineralization and oil concentration of the films is still not clearly defined. In this paper, we propose a compound salt-resistant foaming agent, investigated the influence of the aggregation and adsorption behavior of oil droplets on the liquid films and boundaries, and established a relevant aggregation and adsorption model with the population balance equation. We put forward a liquid film drainage mechanism based on the distribution, aggregation, and transport of oil droplets in the liquid films, so as to explain the changes in foam stability under the action of oil droplets. On the other hand, the viscoelastic analysis of foam fluid is performed with a rheometer, and the results show that in comparison with conventional power-law fluid, foam fluid has a complex rheological behavior for low shear thickening, but high shear thinning.
How liquids transport in the shale system has been the focus because of fracturing fluid loss. In this study, a single-nanopore model is established for liquid transport in shale while considering the slip effect and effective viscosity of confined fluids. Then, the fractal Monte Carlo (FMC) model is proposed to upscale the single-pore model into shale porous media. The effects of different transport mechanisms, shale wettability, and pore characteristic parameters on confined liquid flow in shale rock are investigated. Results show that FMC permeabilities are 2-3 orders of magnitude larger than intrinsic and slip-corrected permeabilities in organic matter. However, the slip effect and effective viscosity have little influence on water flow in inorganic matter. With the contact angle of organic pore (θom) increasing and contact angle of inorganic pore (θin) decreasing, the effective permeability of the whole shale matrix grows in number. The enhancement factor in the situation of θom = 170° and θin = 20° is 4 orders of magnitude larger than the case of θom = 130° and θin = 40°, although the close effective macroscopic contact angle (θeff = 80°) occurs in these two cases, which indicates that shale microscopic wettability has a significant impact on the confined liquid transport. Moreover, with the increase of porosity and maximum pore diameters, shale permeability increases rapidly, but the enhancement factor has the opposite trend. Compared with the tiny impact of the variance of minimum inorganic pore diameters, minimum organic pore diameters have more significant impacts on liquid flow in shale systems, and the enhancement factor also rapidly increases up to 30 times for the case of 0.5 nm because of the strong slip effect.
To address early water breakthrough and poor residual-oil mobilization in low-permeability reservoirs, a core–shell nanosphere/surfactant composite system was developed for profile control and enhanced oil recovery. The core–shell nanospheres were prepared by a semi-continuous seed-growth method, and a target particle-size window of 100–200 nm was selected based on pore-throat/particle matching. The representative sample, HK-0417, had an average particle size of about 120 nm and showed good dispersion stability in formation brine at 45 °C. After blending with the surfactant ALT-603, the system achieved an ultralow oil–water interfacial tension on the order of 10−3 mN/m and reduced the water contact angle of the oil-aged surface from 125° to 70°, indicating a shift toward near-neutral wettability. Core-flooding tests further showed that, under the same chemical dosage, slug injection (HK-0417 followed by ALT-603) demonstrated better performance than co-injection, with higher incremental oil recovery (15.49% vs. 13.17%) and higher plugging efficiency during subsequent water flooding (81.25% vs. 78.46%). The novelty of this work lies in integrating particle-size-window design, controllable preparation of core–shell nanospheres, and direct comparison of injection strategies within one system. The results provide practical guidance for formulation design and injection-mode selection for enhanced oil recovery in low-permeability reservoirs.