The aerial spraying of pesticides by plant protection unmanned aerial vehicles (UAV) is a process in which the spray droplet deposition on target sites occurs under the influence of the downwash wind field. The downwash wind field is the most important factor affecting droplet deposition distribution characteristics in an aerial spray. To understand the mechanism of the downwash wind field, spray tests were conducted at different flight heights by using a DJI UAV, and the downwash wind field in the three-dimensional direction (X-directional wind, Y-crosswind, and Z-vertical wind) was measured by using a wind speed measurement system for UAV. Combined with the droplet deposition of aerial spray, the distribution characteristics of the downwash wind field and the influence of the downwash wind field on droplet deposition were studied. The results showed that it had obvious differences in the distribution of the downwash wind field for UAV at different flight heights. As the flight height increases, the downwash wind field in X-direction and Z-direction showed a strong to weak trend, while the downwash wind field in Y-direction showed an opposite trend. In addition, it was found that the downwash wind field in Y-direction and Z-direction both have a significant influence on droplet deposition. With the increase of flight height, the change of the downwash wind field led to a gradual decrease in droplet deposition in the effective spray area, and droplets deposited more uniformly. For the DJI T16 plant protection UAV in this test, the optimal flight height was 2.0 m, and the downwash wind field had a better improvement effect on droplet deposition. Therefore, in order to make full use of the downwash wind field of UAV, the appropriate flight height should be selected to improve droplet deposition of liquid pesticide and achieve a better control effect for crop disease and pests when UAV is used for aerial spray operations in the field. This study revealed the influence mechanism of the downwash wind field on droplet deposition of aerial spray, and proposed appropriate operation parameters from the perspective of practical operation. It was expected to provide data support for improving the operation quality of aerial spraying and the formulation of field operation specifications.

Plant height is regarded as a key indicator that is crucial for assessing the crop growth status and predicting yield. In this study, an advanced method based on solid-state LiDAR technology is proposed, which is specifically designed to accurately capture the phenotypic characteristics of plant height during the maize growth cycle. By segmenting the scanned point cloud of maize, detailed point cloud data of a single maize plant were successfully extracted, from which stem information was accurately measured to obtain accurate plant height information. In this study, we will concentrate on the analysis of individual maize plants. Leveraging the advantages of solid-state LiDAR technology in precisely capturing phenotypic information, the data processing approach for individual maize plants, as compared to an entire maize community, will better restore the maize’s original growth patterns. This will enable the acquisition of more accurate maize plant height information and more clearly demonstrate the potential of solid-state LiDAR in capturing detailed phenotypic information. To enhance the universality of the research findings, this study meticulously selected key growth stages of maize for data validation and comparison, encompassing the tasseling, silking, and maturity phases. At these crucial stages, 20 maize plants at the tasseling stage, 40 at the flowering stage, and 40 at the maturity stage were randomly selected, totaling 100 samples for analysis. Each sample not only included actual measurement values but also included plant height information extracted using point cloud technology. The observation period was set from 20 June to 20 September 2021. This period encompasses the three key growth stages of maize described above, and each growth stage included one round of data collection, with three rounds of data collection each, each spaced about a week apart, for a total of nine data collections. To ensure the accuracy and reliability of the data, all collections were performed at noon when the natural wind speed was controlled within the range of 0 to 1.5 m/s and the weather was clear. The findings demonstrate that the root mean square error (RMSE) of the maize plant height data, procured through LiDAR technology, stands at 1.27 cm, the mean absolute percentage error (MAPE) hovers around 0.77%, and the peak R² value attained is 0.99. These metrics collectively attest to the method’s ongoing high efficiency and precision in capturing the plant height information. In the comparative study of different stem growth stages, especially at the maturity stage, the MAPE of the plant height was reduced to 0.57%, which is a significant improvement compared to the performance at the nodulation and sprouting stage. These results effectively demonstrate that the maize phenotypic information extraction method based on solid-state LiDAR technology is not only highly accurate and effective but is also effective on individual plants, which provides a reliable reference for applying the technique to a wider range of plant populations and extending it to the whole farmland.