Oil‐paper insulation material is an essential component for oil‐filled transformers, and polyimide (PI) insulation paper is a novel material in the field of electricity. The improvement of insulation class for insulation paper has gained significant attention in recent years. In this study, SiO 2 nanoparticles were modified with a silane coupling agent (KH550), and the KH550‐SiO 2 was added to the fibre membrane through in situ polymerisation. The chemical composition and microcosmic characteristics of the PI porous fibre membrane were characterised using FT‐IR and SEM FT‐IR and SEM. Consequently, the dielectric constant of the composite paper was reduced to 2.3 upon adding 3 wt% of KH550‐SiO 2 , and the dielectric strength reached its maximum value of 85 kV/mm. The results demonstrate that the insulation performance of the KH550‐SiO 2 /PI composite was significantly improved due to the incorporation of nano‐SiO 2 . This establishes an efficient approach for achieving excellent electrical and thermal properties in practical applications using the KH550‐SiO 2 /PI fibre membrane.
Bismaleimide (BMI) resin has great potential in aerospace, electronic, and machinery fields due to its extraordinary thermal stability. Owing to BMI’s lower impact strength, various modified BMI resins have been prepared using CTBN, PEEK, fillers, and hyperbranched polymer to achieve higher impact strength. However, enhancement of toughness causes deterioration of other performance, such as Tg, thermal stability, and brittleness. In this work, BMI resin modified by hyperbranched polyimide (HBPI) was obtained. HBPI designed with flexible segments, unsaturated bonds, and a low degree of branching was synthesized. FT-IR and 13C-NMR were applied to confirm the successful fabrication of HBPI. The mechanical strength and dielectric properties of cured BMI resin containing various levels of HBPI were analyzed systematically. The impact and bending strength were improved significantly with increased HBPI content. When the content of HBPI is 40 wt.%, the impact strength and bending strength reach the maximum value of 32 kJ/mm and 88 MPa. In addition, the BMI cured with HBPI exhibits enhanced bending modulus to the value of 5.9 GPa. Furthermore, the dielectric strength of cured resin was improved to 28.3 kV/mm. The improved mechanical strength and enhanced dielectric properties are attributed to the increasing free volume induced by HBPI. These results indicate the promise of BMI resin modified by HBPI applied in insulating coatings and low dielectric laminates used in high frequency.
The performance of enameled wires has an important impact on new energy vehicle motors. The mainstream practice of existing technology is to improve partial discharge inception voltage (PDIV) by doping powder to inhibit corona and increase varnish thickness, the limitations of which are also obvious. Powder doping has the problem of dispersion stability, and increasing the varnish thickness affects the size and power density of the motor. In this paper, a novel insulation structure design was given. The electronic field stress was controlled by using different dielectric constant materials, and the dielectric constants can be controlled by adjusting the free volume of the polymer. Finally, we specifically create a preparation scheme to increase the corona voltage and the PDIV, without a loss of the breakdown margin of the enameled wire, and the simulation results show that the outermost electric field strength of the enameled wire model decreases by 22.11% and the enameled wire breakdown margin increases by 26.85%.
18 March 2026 in Journal of Materials Science: Materials in Electronics
In view of the requirements for high‐performance epoxy resin (EP) enamelled wire insulating varnish in the rapidly developments of new energy vehicle drive motors, the problems of localised electric field concentration due to the unevenness electric field distribution has to be solved. In this paper, to enhance the corona resistance, insulation, and mechanical properties of EP insulating varnish, the function dielectric gradient structure consists of hyperbranched polyester (HBP) inner layer and silane coupling agent (KH‐550) modified graphene oxide (GO) nonlinear layer are proposed. The results show that the introduction of HBP not only adjusts the dielectric constant of the insulating varnish but also increases the breakdown field strength significantly, and with the increase of K‐GO, the nonlinear conductivity of K‐GO/EP insulating varnish becomes more prominent. Simulation results show that the highest field strength of the structural insulating varnish with different dielectric constant gradients is reduced to 16.7 kV/mm, and the field strength difference of the inner layer is reduced to 0.3 kV/mm, which further reduces the electric field aberration of the neighbouring interfaces as compared to the pure EP insulating varnish. This work provides a new strategy for constructing the dielectric gradient structure to meet the high corona resistance and insulating varnish requirements of high‐voltage motor enamelled wire insulating varnish in actual industrial production.