This article presents the results of comparative investigations of thermal parameters of hybrid sol–gel coatings (named TMZ) prepared from tetraethyl orthosilicate and organically modified 3-methacryloxypropyltrimethoxysilane. The coatings were prepared with the addition of zirconium(IV) tetrapropoxide chelated with methacrylic acid. Two series of samples were investigated: the first series, TMZ-I, TMZ-II and TMZ-III, with different amounts of zirconium, and the second series, TMZ-I/Ce, TMZ-II/Ce and TMZ-III/Ce, with the addition of cerium nitrate. The influence of the amount of zirconium and cerium on the thermal parameters of the sol–gel coatings was next analyzed. Two non-destructive and photothermal techniques were used for this purpose: photothermal radiometry (PTR) and beam deflection spectroscopy (BDS). The thermal diffusivity and conductivity of the coatings were extracted from the frequency experiments and are presented and discussed. The two-layer model was applied to interpret the photothermal spectra. The results obtained using these two techniques are compared and discussed.
1 April 2020 in Journal of Engineering Thermophysics
The article presents the results of comparative investigations of operation modes of the DKVR 10-13 steam boiler system. The investigations were performed in two different modes. In the first mode, the boiler worked only on the gas fuel, whereas in the second mode, the boiler worked on the gas fuel and mazout simultaneously. Each mode requires considering the economic and ecological conditions for the combustion process for each boiler-furnace unit. The exhaust gas from mazout is discharged into the atmosphere and contains substances harmful to people and environment. These emissions can be significantly decreased by optimal control of the combustion process. Optimal organization of the process of combustion of water-mazout emulsion enables decrease in the emission of nitrogen oxides by reducing the excess air via injection of steam or water into the flame. In connection with the above, proper operation of the device must ensure a minimum possible excess of air and minimum temperature of exhaust at the boiler outlet. The experimental research has shown that special technical and technological measures should be used in relation to nitrogen oxide emission by the gas boiler. In turn, simultaneous combustion of gas and mazout allows achieving a similar value of NO\(_{x}\) emissions without need in additional measures.
The constant development of electronic devices and components allows for older systems (which have been well received) with electronic control of combustion processes in municipal thermal energy to be improved to new levels, with significant economic and ecological effects. This article presents details of the development of an improved natural gas combustion quality control system in the modernized DKVR 6.5-13 steam boiler. This paper presents the results of comparative tests of this boiler obtained for various variants of the system operation. It has been proven that maximum boiler efficiency indicators and minimum toxicity of exhaust gases discharged into the atmosphere can be achieved by using a proposed control system. The system uses the regulated residual chemical underburning method, based on simultaneous control of the oxygen and carbon dioxide content in the exhaust gases. As a result of the use of the proposed method, an increase in boiler efficiency was achieved by 1.5–2.1% compared with standard automatic regulation and an increase by 0.3–0.8% compared with regulation based only on the oxygen content in the exhaust gases. These results were achieved by reducing the excess air coefficient. In addition, nitrogen oxide emissions were reduced by 25–30%, which, with a justified safe carbon monoxide content in exhaust gases of up to 250 ppm, reduced the exhaust gas toxicity index to 20%.
Nitrogen oxides are considered to be much more toxic than, for example, carbon monoxide. For this reason, the Authors developed and implemented a method for decrease of NOX emission into the atmosphere from DKVR 10-13 boilers. As an effective method for boilers propose injection of steam into the combustion zone. After series of experimental studies an optimal design of the head for steam injection was developed, according to the proprietary technology. The injector head was kept unchanged while the spraying end caps were modified (Fig. 2). Three levels of possible impact of emissions from boiler on the atmosphere pollution were taken into account during studies. After the analysis, it was assumed that the level of the real maximum emission should be taken as the reference level in relation to which the decrease of NOX emission should be determined. The results obtained by the Authors calculated into mass emission and as objective values of nitrogen oxides concentration calculated into α = 1 (Figures 3 and 4). Realization of the study plan, assumed by the Authors, allowed to determine the optimal parameters of the NOx emission decrease method, assuming the expected 30% level of emission decrease at a limited consumption of injected.
Liquid fuel can be an alternative to solid fuel in non-gasified locations. The mazout for municipal-energy boiler plants is much cheaper than fuel oil. However, this relates to the problem of wastewater disposal from such a boiler plant. A proprietary system for the disposal of bottom water and other sewage-containing mazout has been developed. The solution depends on the proper preparation and burning of a water–mazout emulsion (WME). The emulsion is prepared in a specially designed and developed dosing ejector. By burning the emulsion using the developed system, an efficiency increase of 2–3% was achieved for boilers operating on the mazout fuel. Such a result was achieved due to a reduction in the excess air factor. Moreover, emissions of nitrogen oxides and carbon monoxide were reduced by 30–35% and 70–80%, respectively. In addition due to cleaning the heat-exchange surfaces obtained when working on the WME, the amount of time for productive and more efficient use of the equipment has increased.
The thermal parameters of polybutyl methacrylate–siloxane (PBMA–siloxane) coatings annealed at different temperatures were investigated by means of nondestructive techniques such as Photothermal Radiometry in the frequency domain and frequency-scan photothermal beam deflection spectrometry. The experimental PTR data were interpreted with the use of a model in which the PTR signal is collected from the whole coating’s thickness. A comparison of the results obtained using PTR and BDS methods is presented and discussed.