Yong LIU

Dr. Yong LIU


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 July 2022 in Sensors
Verified
Journal Article
Open access
PDF file
XWXuhuai Wang
Xuhuai Wang
XZXiang Zhang
Xiang Zhang
CYChen Yang
Chen Yang
HLHao Li
Hao Li
YLYong LIU
Yong LIU
In order to study the characteristics of pressure fluctuation during unstable combustion, experimental studies had been conducted on the mechanism model of the swirl combustor and the industrial swirl combustor. The signal of dynamic pressure, heat release rate, and the high-speed flame image in the two combustors were synchronously collected by using dynamic pressure sensors, a photoelectric sensor, and a high-speed camera under normal temperature and pressure. After empirical mode decomposition of the dynamic pressure signal, several intrinsic mode functions were obtained. It was found that the pressure pulsation energy is concentrated in the first three order intrinsic mode function. Through fast Fourier transform spectrum calculation, it was found that the first three order intrinsic mode function pulsation can characterize the changes of heat release rate and air flow pulsation under cold state and flame instability. It showed that the decomposition of the dynamic pressure in the combustor by this method can obtain the main physical processes in its connotation, and provide data processing methods for the induction mechanism of oscillating combustion and combustion diagnosis in an industrial combustor test.

22 April 2025 in Energies
Verified
Journal Article
Open access
PDF file
RLRAN LIU
RAN LIU
JYJingyi Yu
Jingyi Yu
XYXiaoming Yang
Xiaoming Yang
YLYong LIU
Yong LIU
RMRubing Ma
Rubing Ma
YYYidan Yuan
Yidan Yuan
Combustion caused by hydrogen-dominated combustible gas mixtures presents critical threats to nuclear safety during severe accidents in nuclear power plants, primarily due to their propensity for flame acceleration, deflagration, and subsequent detonation. Although the direct initiation of detonation from localized hydrogen accumulation at critical concentrations remains challenging, flame acceleration can induce rapid pressure escalation and lead to deflagration-to-detonation transition under suitable conditions. The ultra-high-pressure loads generated almost instantaneously will pose serious risks to containment integrity and equipment or instrument functionality within nuclear facilities. This paper investigates the flame acceleration mechanism and criterion, which is crucial for precise hydrogen risk assessment. A hydrogen combustion flame acceleration model is developed, integrating both laminar and turbulent flame propagation across multiple control volumes. Validated against the RUT test, the model demonstrates high fidelity with a maximum 3.17% deviation in flame propagation velocity and successfully captures the pressure discontinuity. The developed model enables comprehensive simulation with improved predictive accuracy of the flame acceleration process, making it an essential tool for advancing fundamental understanding of hydrogen behavior and severe accident analysis. This model’s development marks a paradigm in nuclear safety research by providing an analytical instrument for integrated severe accident programs in nuclear power plants, contributing to improving the potential hydrogen risks assessment and management in next-generation reactor safety.

15 August 2025 in Energies
Verified
Journal Article
Open access
PDF file
HSHaitao Sun
Haitao Sun
YZYan Zhao
Yan Zhao
XZXiang Zhang
Xiang Zhang
SWSuofang Wang
Suofang Wang
YLYong LIU
Yong LIU
Combustion instability poses a significant challenge in aerospace propulsion systems, particularly in afterburners that employ bluff-body flame stabilizers. The flame transfer function (FTF) is essential for characterizing the dynamic response of flames to perturbations, which is critical for predicting and controlling these instabilities. This study experimentally investigates the effect of varying the number of fuel injection holes (N = 3, 4, 5, 6) on the FTF and flame dynamics in a model afterburner combustor. Using acoustic excitations, the FTF was measured across a range of frequencies, with flame behavior analyzed via high-speed imaging and chemiluminescence techniques. Results reveal that the FTF gain exhibits dual-peak characteristics, initially decreasing and then increasing with higher N values. The frequencies of these gain peaks shift to higher values as N increases, while the time delay between velocity and heat release rate fluctuations decreases, indicating a faster flame response. Flame morphology analysis shows that higher N leads to shorter, taller flames due to enhanced fuel distribution and mixing. Detailed examination of flame dynamics indicates that different pulsation modes dominate at various frequencies, elucidating the observed FTF behavior. This research provides novel insights into the optimization of fuel injection configurations to enhance combustion stability in afterburners, advancing the development of more reliable and efficient aerospace propulsion systems.

30 January 2025 in Sensors
Verified
Journal Article
Open access
PDF file
XZXiang Zhang
Xiang Zhang
SWSuofang Wang
Suofang Wang
YLYong LIU
Yong LIU
Combustion instability is one of the prominent and unavoidable problems in the design of high-performance propulsion systems. This study investigates the heat release rate (HRR) responses in a triple-nozzle swirling nonpremixed combustor under various thermoacoustic self-excited instability modes. Dynamic pressure sensors and high-speed imaging were employed to capture the pressure oscillations within the combustion chamber and the characteristics of flame dynamics, respectively. The results reveal nonlinear bifurcations in the self-excited thermoacoustic instabilities at different equivalence ratios. Significant differences in flame dynamics were observed across the instability modes. In lower frequency modes, the fluctuations in flame length contribute to the driving force of thermoacoustic instability. In relatively high-frequency modes, HRR fluctuations are dominated by the rolling up and convective processes of wrinkles on the flame surface. Alternating regions of gain and damping are observed on the flame surface. At even higher frequencies, both aforementioned HRR fluctuation patterns are simultaneously observed. These findings provide a deeper understanding of the complex interactions between flame dynamics and thermoacoustic instabilities, offering new insights into the design and optimization of nonpremixed combustion systems. The study underscores the importance of considering the spatial and temporal variations in flame behavior to effectively predict and control thermoacoustic instabilities.

20 July 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
苏赵苏楠 赵
苏楠 赵
CLChongyang Liu
Chongyang Liu
XLXuan Li
Xuan Li
KCKehong Chen
Kehong Chen
YLYong LIU
Yong LIU
To address the difficulty in accurately reproducing the acoustic boundary conditions of an aero-engine combustor, an equivalent simulation method using perforated plates is proposed.Equivalent perforated plates were designed based on the acoustic reflection characteristics of compressor and turbine guide vanes. Their reflection coefficients (0–1000 Hz) were measured under various combustion conditions using the two-microphone method and validated against numerical simulations.The combustor's dominant acoustic response is jointly driven by pressure, temperature, and combustion conditions. The perforated plates effectively modified the acoustic boundaries by shifting the dominant frequency and reducing peak sound pressure. Additionally, the reflection coefficient increased with frequency, with outlet values consistently higher than inlet values , showing strong agreement between experiments and simulations.This perforated-plate model accurately characterizes the acoustic properties of blade rows. It provides reliable technical support for thermoacoustic stability testing, boundary reconstruction, and combustion instability prediction.