Wan Nursheila Wan Jusoh

Dr. Wan Nursheila Wan Jusoh


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 December 2022 in Fire
Verified
Journal Article
Open access
PDF file
WJWan Nursheila Wan Jusoh
Wan Nursheila Wan Jusoh
ATAhmad Faiz Tharima
Ahmad Faiz Tharima
WGWahyunah Ghani
Wahyunah Ghani
NLNur Hafizah Mohamad Lukman
Nur Hafizah Mohamad Lukman
SVSunthaar Visvasathan
Sunthaar Visvasathan
NNNurhayati Nur
Nurhayati Nur
Response time is an important factor in fire operations. A continuous assessment of response time is crucial in order to monitor firefighters’ performance level. An initial assessment of fire response time was conducted for fire stations in categories A-D throughout Malaysia from 2018 to 2020. The categories were determined based on risk profiling scores. In this study, the mean response time and distance travelled for the selected fire stations were calculated. To measure the fire station’s performance, a 10 min standard response time was used as a benchmark. One-way analysis of variance (ANOVA) was also applied to statistically determine any significant differences between mean response time and mean distance travelled. Among the four categories, category C and D fire stations recorded high values for mean distance travelled and mean response time. Category C fire stations recorded the mean response time, at 15.1 min, and distance travelled, 20.1 km. The areas where category D fire stations are located have low population density, resulting in greater coverage for the stations. Most of the fire stations in this category had approximately 13.8 km travel distance with a mean response time of 17.9 min. Category C and D fire stations require a substantial amount of time to reach incident locations due to the low-quality road network and the local topography. A new profiling method for minimizing fire risk based on constant development in these areas might be necessary for future improvement. Additionally, new category C and D fire stations would meet the demands of expanding communities. It is important to note that establishing a demand zone in Malaysia with specific response time could give a better indication of firefighters’ performance in the future.

26 April 2024 in IEEE Transactions on Components, Packaging and Manufacturing Technology
Verified
Journal Article
Closed access
SHSabarina Abdul Hamid
Sabarina Abdul Hamid
MZMuhammad Nubli Zulkifli
Muhammad Nubli Zulkifli
AJAzman Jalar
Azman Jalar
WJWan Nursheila Wan Jusoh
Wan Nursheila Wan Jusoh
MBMaria ABU Abu Bakar
Maria ABU Abu Bakar
MDMichaël Daenen
Michaël Daenen
The aim of this study is to identify the bonding mechanisms of the ultrasonic Al bond on the Mo back-contact layer (Al-Mo system) of a copper indium gallium (de) selenide (CIGS) thin-film photovoltaic (TFPV) solar panel. The bonding mechanism of the Al-Mo system was obtained from the identification of non-stick footprints of Al ribbon and the deformation of ultrasonic Al bonds on the Mo layer using an infinite focus microscope (IFM). The effect of Al bond deformation towards the bondability and electrical behavior of the bonds was evaluated by comparing the results obtained from IFM with the peel force, contact resistance from the transmission line method (TLM), and resistance from a micro-ohm meter, respectively. It is observed that ultrasonic bonding parameters have a major impact on the deformation, bondability, and electrical properties of ultrasonic Al bonds on Mo layers. The bonding mechanism and failure mode can be identified through the IFM examination through the formation of footprints and the evolution of micro-welds (remnant) of ultrasonic Al bonds, and the occurrence of glass substrate cratering. It was found that arithmetical mean deviation of the assessed profile (R a ) of more than 6 μm indicates the ultrasonic Al bond has been formed on the Mo layer. The contact resistance values are more towards representing the variation of intimate contact area, while resistance is more towards representing the resistance of two bonds and the straightness of the Al ribbon.


9 February 2023
Verified
Book Chapter
Closed access
PDF file
WJWan Nursheila Wan Jusoh
Wan Nursheila Wan Jusoh
MHMohd Yusoff Mohd Haris
Mohd Yusoff Mohd Haris
NNNurhayati Nur
Nurhayati Nur
KAKhairul Dahri Mohd Aris
Khairul Dahri Mohd Aris
MBMuhammad Amir Ihsan Basri
Muhammad Amir Ihsan Basri
MMMohd Izhwan Maidu
Mohd Izhwan Maidu