Jianming Yang

Dr. Jianming Yang


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 November 2023 in Gels
Verified
Journal Article
Open access
PDF file
JYJianming Yang
Jianming Yang
Huijun WuHuijun Wu
Huijun Wu
YLYuying Liang
Yuying Liang
JCJian Cen
Jian Cen
XZXianyong Zhang
Xianyong Zhang
Aerogel is widely recognized as a superinsulating material with great potential for enhancing the thermal insulation performance of building walls. It can be applied in various forms such as aerogel plasters (AP), aerogel fibrous composites (AFC), and aerogel concrete (AC) in practical engineering applications. This study aims to investigate the most efficient application form for maximizing building insulation performance while minimizing the amount of aerogel used. To predict the thermal insulation performance of aerogel-insulated walls, a resistance–capacitance network model integrating the aerogels’ effective thermal conductivity model was developed and was validated by comparing it with Fluent simulation software results in terms of surface temperature. Using the validated models, the thermophysical parameters, transient thermal properties, and transmission load were predicted and compared among AP, AFC, and AC walls. The results indicate that using AFC can result in approximately 50% cost savings to achieve the same thermal resistance. After adding a 20 mm thickness of aerogel to the reference wall without aerogel, the AFC wall exhibited the highest improvement in thermal insulation performance, reaching 46.0–53.5%, followed by the AP wall, and then the AC wall, aligning with considerations of microstructural perspectives, thermal resistance distributions, and thermal non-uniformity factors. Therefore, giving priority to AFC use could reduce the required amount of silica aerogel and enhance economic efficiency. These results provide valuable insights for theoretical models and the application of aerogel-insulated walls in building engineering insulation.

19 September 2018 in Nanomaterials
Verified
Journal Article
Open access
PDF file
JYJianming Yang
Jianming Yang
FHFuan He
Fuan He
Huijun WuHuijun Wu
Huijun Wu
YLYuying Liang
Yuying Liang
YWYuxuan Wang
Yuxuan Wang
ZSZhi Sun
Zhi Sun
Understanding the effect of a porous TiO2 nanolayer on the optical scattering and absorption through electrospun fibers is of great importance for the design and development of advanced optical extinction materials. Based on electrospinning and controllable self-assembly techniques, pure electrospun poly(vinylidene fluoride) (PVDF) fibers and TiO2-coated ones with different self-assembly cycles were prepared. The effect of TiO2 self-assembly cycles on surface parameters, e.g., thickness, assembled content, and porosity of the TiO2 nanolayer were determined by scanning electron microscopy, thermogravimetric analysis, and Fourier transform infrared spectroscopy. With an increase in the self-assembly cycles, the TiO2-coated electrospun PVDF fibers presented rougher surfaces and greater average diameters. According to the characterized surface parameters, the effects of the controllable self-assembly on the optical refractive index, absorption index, and infrared extinction were investigated to increase the optical properties of electrospun PVDF fibers. The results indicated that an increase of almost 120–130 cm−1 in infrared extinction could be achieved through the controllable self-assembly with only 5.7 wt. % assembled TiO2 content. This is highly efficient when compared with other coating modes. We believe that this study could give some positive guidance in the design of TiO2-coated electrospun fibers for improving their surface and optical properties.

18 February 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
JYJianming Yang
Jianming Yang
YHYonglang Huang
Yonglang Huang
JHJie Han
Jie Han
HMHongxing Mai
Hongxing Mai
PLPeng Li
Peng Li
This study examined the optical–thermal performance and energy efficiency of electrochromic (EC) glazing in residential buildings situated in regions characterized by hot summers and warm winters. Traditional glazing systems, such as double-layer (DL) and low-emissivity (LE) glazing, often face challenges in achieving an optimal balance between indoor lighting, glare control, and heat regulation. Using EnergyPlus simulations for a typical residential building, this research evaluated the performance of EC glazing under four control strategies, considering seasonal variations (summer and winter), building orientations, and energy demands for cooling, heating, and lighting. The results indicate that EC glazing dynamically adjusts the solar transmittance from 0.320 under low solar radiation to 0.012 at high levels, significantly reducing the glare and convection heat gains. The transmitted radiation heat gain for EC glazing is remarkably only 23.7 J·m−2, compared to 736.8 J·m−2 for DL glazing. Furthermore, EC glazing achieves a total energy consumption of 189.52 MJ·m2, representing a significant 33.0% reduction compared to DL glazing. These findings underscore the potential of EC glazing to improve both the energy efficiency and visual comfort in residential settings. This study highlights the importance of optimizing control strategies, particularly in response to seasonal and directional variations, offering valuable insights for sustainable building design in climates with diverse thermal requirements.

16 October 2024 in Journal of Electrochemical Energy Conversion and Storage
Verified
Journal Article
Closed access
PDF file
GLGaoju Liang
Gaoju Liang
SLShili Lin
Shili Lin
WHWentao Hu
Wentao Hu
XZXianyong Zhang
Xianyong Zhang
JYJianming Yang
Jianming Yang
Accurately estimating the state of charge (SOC) of batteries is crucial for achieving the safety and efficient driving of electric vehicles. To address the negative impact of voltage platform flatness and accumulated errors in current sampling, the SOC estimation method jointing model parameter identification and extended Kalman filter (EKF) algorithm is proposed and verified through simulation in this article. First, the parameter identification method is obtained based on the second-order dual polarization model, and effective identification of the parameters under different SOC is achieved using experimental conditions of hybrid pulse power characteristic and constant current discharge. On this basis, a function model with SOC as the independent variable and model parameters as the dependent variable is established by jointing model parameter identification and EKF algorithm, and the iterative estimation of SOC is achieved through the 1stopt and cftool methods. Finally, the SOC estimation accuracy of the proposed method is validated under three operating conditions that adopt the latest standards and are closer to the actual driving environment. The simulation results show that the SOC estimation method jointing model parameter identification and EKF algorithm has higher accuracy and smaller fluctuations than the traditional ampere-time (AH) integration method, and the mean squared error (MSE) of estimation for the four test conditions are less than 0.29%, 0.72%, and 0.25%, respectively.