A proven method to enhance the mechanical properties of additively manufactured plastic parts is the embedding of continuous fibers. Due to its great flexibility, continuous fiber-reinforced material extrusion allows fiber strands to be deposited along optimized paths. Nevertheless, the fibers have so far been embedded in the parts contour-based or on the basis of regular patterns. The outstanding strength and stiffness properties of the fibers in the longitudinal direction cannot be optimally utilized. Therefore, a method is proposed which allows to embed fibers along the principal stresses into the parts in a load-oriented manner. A G-code is generated from the calculated principal stress trajectories and the part geometry, which also takes into account the specific restrictions of the manufacturing technology used. A distinction is made between fiber paths and the matrix so that the average fiber volume content can be set in a defined way. To determine the mechanical properties, tensile and flexural tests are carried out on specimens consisting of carbon fiber-reinforced polyamide. In order to increase the influence of the principal stress-based fiber orientation, open-hole plates are used for the tensile tests, as this leads to variable stresses across the cross section. In addition, a digital image correlation system is used to determine the deformations during the mechanical tests. It was found that the peak load of the optimized open-hole plates was greater by a factor of 3 and the optimized flexural specimens by a factor of 1.9 than the comparison specimens with unidirectional fiber alignment.

An existing challenge in the use of continuous fiber reinforcements in additively manufactured parts is the limited availability of suitable fiber materials. This leads to a reduced adaptability of the mechanical properties to the load case. The increased design freedom of additive manufacturing allows the flexible deposition of fiber strands at defined positions, so that even different fiber materials can be easily combined in a printed part. In this work, therefore, an approach is taken to combine carbon and aramid fibers in printed composite parts to investigate their effects on mechanical properties. For this purpose, tensile, flexural and impact tests were performed on printed composite parts made of carbon and aramid fibers in a nylon matrix with five different mixing ratios. The tests showed that the use of hybrid composites for additive manufacturing is a reasonable approach to adapt the mechanical properties to the loading case at hand. The experiments showed that increasing the aramid fiber content resulted in an increase in impact strength, but a decrease in tensile and flexural strength and a decrease in stiffness. Microstructural investigations of the fracture surfaces showed that debonding and delamination were the main failure mechanisms. Finally, Rule of Hybrid Mixture equations were applied to predict the mechanical properties at different mixture ratios. This resulted in predicted values that differed from the experimentally determined values by an average of 5.6%.

Recent research efforts have highlighted the potential of hybrid composites in the context of additive manufacturing. The use of hybrid composites can lead to an enhanced adaptability of the mechanical properties to the specific loading case. Furthermore, the hybridization of multiple fiber materials can result in positive hybrid effects such as increased stiffness or strength. In contrast to the literature, where only the interply and intrayarn approach has been experimentally validated, this study presents a new intraply approach, which is experimentally and numerically investigated. Three different types of tensile specimens were tested. The non-hybrid tensile specimens were reinforced with contour-based fiber strands of carbon and glass. In addition, hybrid tensile specimens were manufactured using an intraply approach with alternating carbon and glass fiber strands in a layer plane. In addition to experimental testing, a finite element model was developed to better understand the failure modes of the hybrid and non-hybrid specimens. The failure was estimated using the Hashin and Tsai–Wu failure criteria. The specimens showed similar strengths but greatly different stiffnesses based on the experimental results. The hybrid specimens demonstrated a significant positive hybrid effect in terms of stiffness. Using FEA, the failure load and fracture locations of the specimens were determined with good accuracy. Microstructural investigations of the fracture surfaces showed notable evidence of delamination between the different fiber strands of the hybrid specimens. In addition to delamination, strong debonding was particularly evident in all specimen types.

In the development of innovative and high-performance products, design expertise is a critical factor. Nevertheless, novel manufacturing processes often frequently lack an accessible comprehensive knowledge base for product developers. To tackle this deficiency in the context of emerging additive manufacturing processes, substantial design knowledge has already been established. However, novel additive manufacturing processes like continuous fiber-reinforced material extrusion have often been disregarded, complicating the process's wider dissemination. The importance of design knowledge availability is paramount, as well as the need for user-friendly design knowledge preparation, standardized structure, and methodological support for accessing the accumulated knowledge with precision. In this paper, we present an approach that provides formalized opportunistic and restrictive design knowledge, ensuring both the comprehensive exploitation of process-specific potentials and the consideration of restrictive limitations in the construction of components. Opportunistic knowledge, presented as principle cards, is systematically derived, prepared, and made accessible. Moreover, an access system is developed to ensure the comprehensive utilization of process-specific potentials throughout the development process. Furthermore, we propose linking these principles through a synergy and conflict matrix, aiming to consider synergistic principles and identify potential conflicts at an early stage. Additionally, an approach to provide restrictive design knowledge in the form of a design rule catalog is proposed. The application of the knowledge system is demonstrated exemplarily using a weight-optimized component.