Ciprofloxacin (CIP) has been listed in the last version of the surface water due to its ability to kill human cells by inhibiting the activity of DNA topoisomerase IV. Thus, CIP, along with other antibiotic pollution has become a serious threat to the environment and public health. Ozonation has been used as an advanced technique that is applied in wastewater treatment to remove CIP, but the primary limitation of this method is the low solubility of ozone in water. This study is the first report of CIP removal in a scale-up of its aqueous solution using a self-developed aerator pump-enhanced ozonation (APO) system, which only employs a propeller and a zigzag arrangement of meshes. This aerator pump decreased the size of ozone bubbles by 90% and increased the effective ozone solubility to 0.47 ppm. The mechanism of degradation of CIP is attributed to an oxidation reaction of the antibiotic with reactive oxygen species, such as hydroxyl, oxygen, and hydroperoxyl radicals, generated on the surface of the ozone microbubbles. It was found that the rate and efficiency of degradation of CIP using the APO system were 3.64 × 10−3/min and 83.5%, respectively, which is higher compared with those of conventional flow ozonation (FO) systems (1.47 × 10−3/min and 60.9%). The higher degradation efficiency of CIP by the APO system was also revealed by its higher electrical energy efficiency (0.146 g/kWh), compared to that of the FO system (0.106 g/kWh). The degradation of CIP was also monitored by the resulting antibacterial activity against Escherichia coli and Staphylococcus aureus.
26 February 2019 in Journal of Physics: Conference Series
Ozone that was generated by using dielectric barrier discharge plasma (DBDP) reactor has been investigated. In this study, we compared ozone production with reactor series and parallelled at atmospheric pressure. The reactor used models of a wire mesh - aluminum foil configuration. The first reactor uses a series circuit with two reactors and the second reactor uses a parallel circuit with two reactors. Ozone was produced by DBDP reactor using AC high Voltage. Oxygen that source of ozone has been taken from the pure oxygen and natural gas. Some analysis conducted including the variation of voltage, the flow rate of gas and type of source gas which affect produced concentration. Some parameters varied including voltage from 0 - 10 kV and the flow rate of gas 4 - 12 L / min. The results showed that ozone concentration in the series reactor is higher than that of the parallel reactor. The series reactor could produce ozone with a concentration of 348 ppm at a voltage of 10 kV. Then the parallel reactor of ozone could produce with a concentration of 240 ppm at a voltage of 10 kV. We found that series reactor could produce more high ozone concentration at the same voltage.
1 March 2019 in Journal of Physics: Conference Series
Research on the power analysis of ozone generator for high capacity production has been done. We used an ozone generator with capacity of 100 grams/hour. The ozone generator was developed by providing dielectric barrier discharge (DBD) plasma reactor. DBD reactor was made of a glass tube as dielectric material and stainless-steel mesh wire as electrodes. An AC high voltage was used as a power supply. The pure oxygen and free air were used as source of gas. The produced ozone was measured at some variation of voltage, i.e. 2.5-5.7 kV with constant flowrate of 20 L/min and dissolving durration into KI solution of 2 min. The ozone concentration was measured by reacting ozone to potassium iodide (KI), as an ozone scavenger solution. The results showed that ozone capacity increase with increasing of applied voltage. The minimum and maximum capacity of ozon with pure oxygen input obtained at voltage of 2.5 kV and 3.6 kV, while with free air input obtained at voltage of 2.5 kV and 5.7 kV. Furthermore, ozone capacity of 100 gr/h with pure oxygen input obtained at power of 6.2 watt while with free air input obtained at power of 17.6 watt.
26 February 2019 in Journal of Physics: Conference Series
Microplastics (MPs) have emerged as persistent environmental pollutants with adverse effects on ecosystems and human health. Conventional removal methods, such as filtration and sedimentation, primarily rely on physical separation without addressing the degradation of MPs, leading to their accumulation and the risk of secondary pollution. This review explores the potential of advanced oxidation processes (AOPs), including photocatalysis, electrochemical oxidation, Fenton processes, sulfate radical-based oxidation, sonochemical treatment, ozonation, and plasma technologies, which generate reactive oxygen and nitrogen species capable of promoting polymer chain scission, microbial biodegradation, and the oxidative fragmentation and mineralization of MPs into non-toxic byproducts. Hybrid AOP systems combined with biological treatments or membrane-based filtration are also examined for their effectiveness in degrading MPs, as well as for scalability and the environmental impacts of their byproducts when integrated into existing wastewater treatment systems. The review further discusses challenges related to operational parameters, energy consumption, and the formation of secondary pollutants. By identifying current knowledge gaps and future research directions, this review provides insights into optimizing AOPs and integrations of AOPs with biological treatments or membrane-based processes for sustainable MP remediation and water treatment applications.