Lauren Bowers

Mrs. Lauren Bowers

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 September 2019 in Toxicology Letters
Verified
Journal Article
Closed access
MFMariana Farcas
Mariana Farcas
ASAleksandr B. Stefaniak
Aleksandr B. Stefaniak
AKAlycia K. Knepp
Alycia K. Knepp
LBLauren Bowers
Lauren Bowers
WMWilliam K. Mandler
William K. Mandler
YQYong Qian
Yong Qian

24 November 2022
Verified
Book Chapter
Closed access
PDF file
Mohammed Abbas VirjiMohammed Abbas Virji
Mohammed Abbas Virji
LBLauren Bowers
Lauren Bowers
RLRyan F. LeBouf
Ryan F. LeBouf

17 April 2026 in Safety
Verified
Journal Article
Open access
PDF file
ASAleksandr B. Stefaniak
Aleksandr B. Stefaniak
EBElizabeth D Brusak
Elizabeth D Brusak
LBLauren Bowers
Lauren Bowers
AKAustin Kron
Austin Kron
SFSherri A. Friend
Sherri A. Friend
Mohammed Abbas VirjiMohammed Abbas Virji
Mohammed Abbas Virji
Powder bed fusion (PBF) and directed energy deposition (DED) additive manufacturing use feedstock powders that contain metals associated with skin diseases. We performed a survey of surface contamination and limited task-based dermal exposure assessment (four employees) at a PBF and DED facility. Skin wipes of wrists for two employees in the PBF room had higher post-task levels of chromium, cobalt, molybdenum, and nickel. Personal clothing worn by PBF employees showed evidence of contamination with metals as did personal protective equipment (PPE). Microscopy analysis documented contamination of metals throughout most areas of the facility. Levels of metals on surfaces throughout the facility were (ng/cm2) <5.0–7247 (aluminum), <0.2–4899 (chromium), <background-6.0 (chromium VI), 0.03–468.1 (cobalt), 1.6–100.0 (copper), 32.9–19,000 (iron), 0.01–789.0 (molybdenum), 0.1–12,058 (nickel), 0.1–482.8 (titanium), and 0.07–9.3 (vanadium). Levels were significantly lower in administrative areas compared with the production area but generally did not differ among powder handling and non-powder handling rooms in production. The small number of participants in the dermal exposure assessment and uniqueness of the facility might limit generalizability of the results. At least for this facility, steps to lower skin contact with metals can include washing, consistent use of PPE, and increasing awareness of dermal hazards among workers. Approaches to reduce migration of metals throughout a facility can include using adhesive (“tacky”) mats and boot covers and frequent wet cleaning of floors, tools, handles, and high touch surfaces.

1 April 2026 in Recycling
Verified
Journal Article
Open access
PDF file
ASAleksandr B. Stefaniak
Aleksandr B. Stefaniak
LBLauren Bowers
Lauren Bowers
CWCallee Walsh
Callee Walsh
SPSonette du Preez
Sonette du Preez
EBElizabeth D Brusak
Elizabeth D Brusak
JPJeanetta Du Plessis
Jeanetta Du Plessis
Distributed recycling of high-density polyethylene (HDPE) into filament for use in material extrusion 3D printing has been proposed as part of a circular economy. There is a gap in the understanding of the potential for HDPE to release contaminants that are potentially hazardous to human health during reuse. Herein, HDPE from post-consumer packaging waste was sorted into food and non-food (NF) streams and virgin HDPE was taken as a benchmark material. All materials were extruded into filaments and recycled multiple times while monitoring emissions. In general, particle and organic chemical emissions decreased by 93 to 99% and 73 to 99%, respectively, with increased reprocessing cycle without appreciable decline in mechanical (Young’s modulus decreased by 5 to 16%), processability (melt flow index stable from 0.2 to 0.7 g/10 min for waste plastics), and thermal properties (crystallinity ranged from a 6% decrease to a 9% increase) of plastics. An exception was a sub-stream of NF plastic that had increased particle emissions (up to 3100%) with reprocessing cycle. Reductions in emissions during filament extrusion appeared to be more influenced by reprocessing cycle than by any specific process step (grinding, etc.). The progressive decline in emissions without appreciable loss of polymer integrity could be exploited to pre-condition HDPE to reduce potential hazardous emissions prior to extruding into filament. This work helps fill the knowledge gap on approaches to recycling plastics in distributed settings such as home-based businesses, which is critical for developing effective recommendations for controls to enable safe work practices such as the use of ventilation to minimize exposures.