Understanding the kinetics of the crystallization process for organometal halide perovskite formation is critical in determining the crystalline, nanoscale morphology and therefore the electronic properties of the films produced during thin film formation from solution. In this work, in situ grazing incidence small-angle X-ray scattering (GISAXS) and optical microscopy measurements are used to investigate the processes of nucleation and growth of pristine mixed halide perovskite (MAPbI3–xClx) crystalline films deposited by bar coating at 60 °C, with and without additives in the solution. A small amount of 1,8-diiodooctane (DIO) and hydriodic acid (HI) added to MAPbI3–xClx is shown to increase the numbers of nucleation centers promoting heterogeneous nucleation and accelerate and modify the size of nuclei during nucleation and growth. A generalized formation mechanism is derived from the overlapping parameters obtained from real-time GISAXS and optical microscopy, which revealed that during nucleation, perovskite precursors cluster before becoming the nuclei that function as elemental units for subsequent formation of perovskite crystals. Additive-free MAPbI3–xClx follows reaction-controlled growth, in contrast with when DIO and HI are present, and it is highly possible that the growth then follows a hindered diffusion-controlled mechanism. These results provide important details of the crystallization mechanisms occurring and will help to develop greater control over perovskite films produced.
A predictive model correlating the properties of a catalyst with its performance would be beneficial for the development, from biomass waste, of new, carbon-supported and Earth-abundant metal oxide catalysts. In this work, the effects of copper and iron oxide crystallite size on the performance of the catalysts in reducing nitrogen oxides, in terms of nitrogen oxide conversion and nitrogen selectivity, are investigated. The catalysts are prepared via the incipient wetness method over activated carbon, derived from palm kernel shells. The surface morphology and particle size distribution are examined via field emission scanning electron microscopy, while crystallite size is determined using the wide-angle X-ray scattering and small-angle X-ray scattering methods. It is revealed that the copper-to-iron ratio affects the crystal phases and size distribution over the carbon support. Catalytic performance is then tested using a packed-bed reactor to investigate the nitrogen oxide conversion and nitrogen selectivity. Departing from chemical characterization, two predictive equations are developed via an artificial neural network technique—one for the prediction of NOx conversion and another for N2 selectivity. The model is highly applicable for 250–300 °C operating temperatures, while more data are required for a lower temperature range.
In situ wide-angle X-ray scattering (WAXS) has been measured during the spin coating process used to make the precursor films required for the formation of thin films of perovskite. A customized hollow axis spin coater was developed to permit the scattered X-rays to be collected in transmission geometry during the deposition process. Spin coating is the technique most commonly used in laboratories to make thin perovskite films. The dynamics of spin-casting MAPbI3–xClx and FAPbI3–xClx films have been investigated and compared to investigate the differences between the dynamics of MAPbI3–xClx and FAPbI3–xClx film formation. In particular, we focus on the crystallization dynamics of the precursor film formation. When casting MAPbI3–xClx, we observed relatively fast 1D crystallization of the intermediate product MA2PbI3Cl. There was an absence of the desired perovskite phase formed directly; it only appeared after an annealing step that converted the MA2PbI3Cl to MAPbI3. In contrast, slower crystallization via a 3D precursor was observed for FAPbI3–xClx film formation compared to MAPbI3–xClx. Another important finding was that some FAPbI3–xClx perovskite was generated directly during spin-casting before annealing. These findings indicate that there are significant differences between the crystallization pathways for these two perovskite materials. These are likely to explain the differences in the lifetimes of the resulting perovskite solar cell devices produced using FA and MA cations.
18 August 2011 in The European Physical Journal Applied Physics
Research and development activities in organic solar cells have been intensified in the last two decades, and the reported energy conversion efficiency in small cell samples is rapidly increased. However, the relation between cell performance and material preparation conditions is not fully understood. In this work charge carrier recombination processes in hybrid poly-3-octylthiophene (P3OT)/cadmium sulfide (CdS) photovoltaic cells were analyzed as a function of structural and optoelectronic properties of chemical bath deposited CdS thin films. The temperature of the bath solution varied between 60 and 80 °C, and the deposition time from 1 to 3 h. Charge carrier recombination times in CdS films were measured with photoconductance decay technique, whereas the same time in P3OT films was estimated by Time-of-Flight method. Charge carrier recombination rates at CdS/P3OT interface were determined by transient photovoltage technique. It is found that CdS films grown at lower solution temperature (60 °C) give a higher charge carrier recombination rate at CdS/P3OT interface and larger short-circuit current density and energy conversion efficiency values in the corresponding solar cells, in comparison with the 80 °C deposited ones. This improvement could come from the reduction of charge carrier trap density inside grains as well as at grain boundaries in lower temperature deposited CdS films.