As’ad Munawir

As’ad Munawir


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 December 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
LDLydia Darmiyanti
Lydia Darmiyanti
AMAs’ad Munawir
As’ad Munawir
ARArief Rachmansyah
Arief Rachmansyah
YZYulvi Zaika
Yulvi Zaika
ESEko Andi Suryo
Eko Andi Suryo
Clay is a soil with low permeability. Clay is considered a problematic soil besides peat soil. The main problem with clay is its mineralogy. Expansive clay soils contain the minerals kaolinite, illite, and montmorillonite. Montmorillonite has weak bonds between its layers. These weak bonds make the soil easily incorporated, one of which is water. Water approaching expansive soil will bond with it and cause swelling. Expansive soil improvement studies have been conducted. One of them is electrokinetic. Expansive soil from Karawang, Indonesia is one of the soils with a high swelling index. This is because montmorillonite is inside. The Karawang expansive soil will be improved by flowing several salt solutions with various voltages. The applied voltage will flow the solution from the cathode to the anode and fill the clay minerals. Four voltage variants will be applied with the same electrokinetic application time. The mineralogy of soil before and after electrokinetic improvement undergone changes. The changes can be seen from SEM and XRF testing. The improved soil changed its physical properties from clay with high plasticity to clay with low plasticity. Chemical elements from salt solution trap in montmorillonite then make positive changes in soil mineralogy, soil physical properties, and mechanical properties. The mechanical properties can be seen in a decrease in the C value and an increase in the soil angle of friction after electrokinetic improvement. After electrokinetic improvement using calcium chloride, the lowest soil cohesion value was 12.356 kg/cm2 at 12 V. After electrokinetic improvement with calcium dioxide, the lowest cohesion value at 12 V voltage is 19.22 kg/cm2. In barium sulfate solution, the lowest soil cohesion at 15 V is 12.16 kg/cm2. The soil swelling value decreased after improvement with calcium chloride to 0.008 % from 0.027 %. The research results in calcium chloride with 12 V give optimized results on soil improvement with electrokinetics

22 December 2023 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AGAnita Setyowati Srie Gunarti
Anita Setyowati Srie Gunarti
YZYulvi Zaika
Yulvi Zaika
AMAs’ad Munawir
As’ad Munawir
ESEko Andi Suryo
Eko Andi Suryo
HHHarimurti Harimurti
Harimurti Harimurti
Expansive soil causes road construction damage in the form of cracks or deformations due to changes in moisture content. One method to address this issue is soil stabilization using additive materials. Special additives can sometimes be expensive; hence it is necessary to use additive materials based on industrial waste as a waste management solution to solve the problem of expansive soil as a road construction subgrade. This study aims to analyze the effects of adding two types of industrial waste, namely fly ash (FA) and waste foundry sand (WFS), regarding the microstructure, physical, and mechanical properties of expansive soil. The method of stabilizing expansive soil involves mixing the soil with 9 % FA and various levels of WFS (0 %, 7.5 %, 10 %, 15 %) based on the dry weight of the soil. Microstructure testing includes quantitative X-ray diffraction and scanning electron microscopy. Physical property testing includes specific gravity, Atterberg limits and sieve analysis. Mechanical testing, i.e. compaction, California Bearing Ratio, swelling, and Triaxial tests were conducted. Soil stabilized with 9 % FA and 15 % WFS shows a significant increase in the internal friction angle and cohesion, reducing swelling by 67.18 % compared to the original soil swelling. The addition of 9 % fly ash and 15 % WFS to expansive soil reduces the content of montmorillonite. Natural expansive soils have a very poor soaked CBR of 0.94 %, while stabilized soils with 9 % FA and 15 % WFS have a soaked CBR of 6.46 %. This means that the soaked CBR of the stabilized soil meets the minimum CBR required for road subgrade construction. A mixture of 9 % FA and 15 % WFS in expansive soil can be recommended as a material for stabilizing expansive soil due to its ability to improve microstructure and mechanical properties

21 August 2024 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AGAnita Setyowati Srie Gunarti
Anita Setyowati Srie Gunarti
YZYulvi Zaika
Yulvi Zaika
AMAs’ad Munawir
As’ad Munawir
ESEko Andi Suryo
Eko Andi Suryo
HHHarimurti Harimurti
Harimurti Harimurti
The issue of subgrade soil often involves unstable soil properties, such as low bearing capacity, susceptibility to expansion and shrinkage, and vulnerability to erosion and deformation due to traffic loads and weather conditions. Unstable subgrade soil can cause various infrastructure problems, including cracks, settlement, and damage to road surfaces. Therefore, stabilizing subgrade soil is an important step to ensure the reliability and longevity of highways. One effective and sustainable method for subgrade soil stabilization is by utilizing local waste materials. The use of local waste materials such as fly ash (FA) and waste foundry sand (WFS) not only improves the physical and mechanical properties of the soil but also helps reduce environmental impact by repurposing pollutants. This study aims to analyze the effect of the thickness of subgrade layers stabilized with FA and WFS on bearing capacity. The initial stage includes examining the physical and mechanical properties of natural soil and soil stabilized with FA and WFS. The waste content used is 9 % FA and 15 % WFS by dry weight of the soil. Subgrade modeling was conducted using a steel box measuring 60×60×60 cm with a soil thickness of 30 cm. Load testing was carried out on 5 layer variants that had undergone 4 days of curing. The study results found that the ultimate bearing capacity (qult) of 890 kPa was produced by the V4 layer, which is a subgrade with a 30 cm thick layer of soil stabilized with FA and WFS at a settlement of 6 mm. The bearing capacity ratio of 2.87 means that the subgrade with a 30 cm thick layer of soil stabilized with FA and WFS experienced an improvement in bearing capacity of 2.87 times that of the subgrade with untreated soil material. The results obtained can be applied in practice to the local geotechnical conditions of the project site in West Java, including natural soil properties and seasonal changes

14 August 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
AMAs’ad Munawir
As’ad Munawir
HHHarimurti Harimurti
Harimurti Harimurti
QSQueen Arista Rosmania Putri Sumarsono
Queen Arista Rosmania Putri Sumarsono
Earthquakes are a high-risk natural phenomenon in Indonesia, which is between three tectonic plates: the Eurasian, Pacific, and Indo–Australian plates. This study examines the response of bored piles with asymmetrical pile cap in the Auditorium Building of Brawijaya University to seismic loads, which is still rare to conduct this research. This study assessed based on 3D finite element-numerical approach, where lateral resistance and p-multiplier values compared on the effects of combination lateral loads, pile stiffness, and soil stiffness. The behavior of lateral resistance and deflection group piles with asymmetrical pile cap and single pile with square pile cap gives a good agreement. The side slope of the pile cap can increase the shear zone, increase the lateral resistance, and the most considerable lateral resistance to the lowest occurs in the horizontal direction, opposite the loading direction. In addition, the pile configuration that is not symmetrical gives an increasing p-multiplier value followed by an increasing deflection and the p-multiplier from the 3D finite element method was within the recommended range.

30 October 2025 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
ACAgata Iwan Candra
Agata Iwan Candra
AMAs’ad Munawir
As’ad Munawir
YZYulvi Zaika
Yulvi Zaika
ESEko Andi Suryo
Eko Andi Suryo
In sandy soils, skin resistance efficiency is critical, as it governs load capacity, settlement, and foundation cost. This study investigates pile foundations with directional surface asperities embedded in uniform sand to clarify the limited knowledge of how asperity orientation (cranial vs. caudal), geometric ratio (L / H), and pile diameter affect axial load transfer. Experimental tests were conducted on steel piles with diameters of 10, 12, and 15.85 mm under smooth, cranial, and caudal conditions with L / H ratios of 20, 26.67, and 33.33. Axial compression tests following ASTM D1143-20 in controlled dry sand provided ultimate load and shaft resistance data, validated by one-way ANOVA. The results show that cranial asperities consistently outperformed other surfaces, with the Cr L / H 20 configuration on the 15.85 mm pile reaching 0.368 kN, a 392.51% increase over smooth piles, while caudal asperities achieved only 134.30%. Cranial asperities also mobilized shaft resistance more uniformly along the pile, reducing end-bearing reliance. This performance is explained by stronger passive interaction at the pile-soil interface, which raises normal stress and friction mobilization. The distinctive feature of this research is the identification of the L / H ratio as a measurable design parameter, with L / H = 20 found to be optimal, in contrast to previous studies that described roughness only qualitatively. The findings demonstrate practical potential for applying cranial asperity designs in pile foundations for light- to medium-scale infrastructure on sandy soils, such as bridges, wharves, and transmission towers, enabling shorter or fewer piles without compromising safety while improving cost efficiency and geotechnical performance

30 April 2025 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
AMAs’ad Munawir
As’ad Munawir
YZYulvi Zaika
Yulvi Zaika
ESEko Andi Suryo
Eko Andi Suryo
NCNuril Charisma
Nuril Charisma
AAArief Alihudien
Arief Alihudien
This study examines how increase in pore water pressure weakens the sand foundation, triggers liquefaction and lateral shift. This is related to the interaction of pressure, density, depth, and load through experiments and simulations to increase the foundation design. Numerical analysis using UBC3D-PLM 3D plaxis, while experimental tests are carried out with a 2.2 kW electric motor-powered table. Experiment uses an acrylic ground box 0.5×1×1.5 m3 which is strengthened by steel. The foundation model is in the form of a 2×2 pole group with four pillars and pile caps. The results of the study showed an increase in pore water pressure due to vertical and earthquake loads could trigger liquefaction and vertical deformation. Numerical analysis shows a surge in pressure in 20 seconds, in the case exceeding the 7.0 ratio, shows full liquefaction. The vibrating table experiment (relative density of 10 %) shows RU values close to 1, confirming the potential for liquefaction. Both experiments and simulations indicate rapid initial deformation before stabilization. Pore water pressure jumped to the critical level before stable, indicating the potential for full liquefaction. Non-linear vertical deformation confirms significant soil changes below the dynamic load. This study identifies the limit of the pressure ratio for partial and full liquefaction and soil response to vertical and seismic loads. The combination of numerical and experimental data allows the analysis of vertical deformation of foundation stability. This finding supports the design of earthquake resistant foundations and geotechnical risk assessment, although its application must consider soil conditions and limitations of numeric models, so it is necessary to be further calibration for prediction accuracy