We propose a hybrid dispersion compensation method to design wideband fixed-beam leaky-wave antennas (LWAs), with the tilting angle customizable in both forward and backward quadrants. In a previous work, a triangular dispersive prism constituted by metallic pins was presented to compensate for the dispersion of traditional LWAs and achieve a squint-free radiation in a relative bandwidth of 20%. However, that design suffered from the drawbacks of large geometry and limited angular range. To overcome these limitations, here a broadband gradient metasurface based on geometric phase theory is loaded in front of the prism to customize the radiation angle and reduce the total prism size. In addition, a novel ridged gap waveguide is employed to improve the linearity of LWA dispersion, which is beneficial to maintain the bandwidth of LWA with reduced size. Two examples are presented to demonstrate the excellent performance of the designed antennas. One antenna radiates at an angle of 39.5° in a squint-free bandwidth of 20%, but the prism size is decreased to a quarter of the original one, while the other realizes a broadside radiation with a squint-free bandwidth of 18%. Good agreement is exhibited between simulated and experimental results. The proposed method can be further extended to compensate for the dispersion of antenna arrays and improve the angular stability of the radiation beams in a large frequency band.
17 December 2019 in IEEE Transactions on Antennas and Propagation
In this paper, we propose a wideband fully-metallic impedance-matching horn lens antenna based on glide symmetry realized in the gap waveguide technology. A multiple iterative method is adopted, which overcomes the limitation of large phase deviations at the interface of traditional lens antennas, thus increases the directivity as a result. Moreover, the glide-symmetric configurations of inner metallic pins within the gap waveguide are employed to construct the artificial dielectric lens, with the advantage of the ultra-low dispersion, which is especially helpful to broaden the working bandwidth and improve the lens performance. The antenna is fed by a stepped double ridged gap waveguide which can easily excite the antenna working in a wide band. To reduce the undesired reflections at the antenna aperture, the antenna is ended with a tapered structure as an impedance transition. A prototype of the horn lens antenna is manufactured and measured, showing a broad operation bandwidth from 12 to 18.5 GHz with S11 less than -10 dB. The antenna can be further extended to the millimeter band due to the low losses of the gap waveguide at high frequencies and the iterative method can also be applied to other types of lens antenna designs.
18 November 2020 in IEEE Transactions on Antennas and Propagation
Leaky wave antenna is known as a type of travelling antenna with dispersive frequency responses, which has found important applications in modern communication, imaging and radar systems. The beam scanning rate is a key consideration in some applications, since it can minimize the bandwidth requirement of the system, during the scanning in broad angular regions. However, the sweeping linearity, namely the scanning angular range per unit frequency, is seldom taken into account at the same time in the published literature. In this article, we propose a waveguide-type leaky-wave antenna working from 11.1 GHz to 12 GHz. By loading periodical pins with glide symmetry in the waveguide, it is possible to manipulate the dispersion properties of the fast wave mode, hereby giving rise to a good balance between the scanning rate and sweeping linearity. This scenario has been validated by numerical simulation and experiment with excellent agreement. The measurement results reveal that the scanning angles have been increased to range from 16.7° ~67.5° varying the frequency from 11.1 to 12.1 GHz. The relative average scanning rate is enhanced up to 589.3°, with high sweeping linearity.
Single-mode operation in a rectangular waveguide is very important, since the existence of multimodes may arouse distortions of carried signals due to the modal dispersion. High-order mode means multiple periods of field in the transverse cross section, with distinct electromagnetic properties from the dominant mode. Although numerous methods are proposed to achieve mode selection within the waveguide, they only permit specific high-order modes to survive in a frequency range. However, it still remains a great challenge to control the bandwidth freely for single-mode operation. Here, we propose an approach for high-order mode generation, in which the desired mode operates in the band gap of other modes, and the working bandwidth can be engineered independently by reducing the symmetry of the loaded periodic metallic ridges in the waveguide. Two examples are demonstrated, where only and modes are supported. The proposed method can also be applied to generate other high-order TE modes in the future.
2 June 2021 in IEEE Transactions on Antennas and Propagation
In this article, a $1\times 12$ millimeter-wave (mmW) linearly tapered slot antenna (LTSA) array, fed by high-order waveguide modes, is introduced. Due to the antiphase characteristic between adjacent channels of a power divider based on the TE ${}_{2n,0}$ mode waveguide, the cross-polarized E-field components can cancel each other out in an endfire direction, even in the case of a relatively thick substrate. Moreover, the electric separations between the adjacent channels employed in a traditional substrate integrated waveguide (SIW) power divider can be removed without affecting the field distributions. This facilitates in improving robustness to avoid fabrication errors. Additionally, a general condition of generating a single high-order mode with symmetrical protection is outlined. By combining two antiphase TE 30 mode waveguides, an equivalent TE 60 mode waveguide with six identical output channels is realized. To feed a 12-element array, two equivalent TE 60 mode waveguides are employed as an equivalent TE 12,0 mode-feeding network. Instead of the complex 1-to- $n$ -way power divider and relatively thin substrate featured in previous works, the high-order mode-fed LTSA array introduced in this study is able to operate over 26.5–30 GHz with substrate height of 2 mm ( $0.19\lambda _{0}$ ), yielding a cross-polarization level of less than −15 dB.
Near-field high-resolution synthetic aperture radar (SAR) imaging is mostly accompanied by a large number of data acquisition processes, which increases the system complexity and device cost. According to extensive reports, reducing the number of sampling points of a radar in space can greatly reduce the amount of data. However, when spatial sparse sampling is carried out, a ghost normally appears in the imaging results due to the high side lobes generated in the azimuth. To address this issue, a technique is introduced in this paper to recover the blank data through amplitude and phase compensation based on the correlation between sparse array sampling through adjacent points. Firstly, the data sampled by the sparse array is compressed in the range direction to obtain the expected data slices in the same range direction. Then, the blank element of the slice is compensated for with amplitude and phase to obtain full aperture data. Finally, the matched filter method is used to aid in the image reconstruction. The simulation results verified that the method proposed in this paper can effectively reconstruct the image under two kinds of sparse sampling conditions. Thus, a simple single-input single-output (SISO) synthetic aperture radar imaging test bench is established. Compared with the results of a 1 mm (1/4 ) sampling interval, the quality of the reconstructed image under the condition of a 4 mm (1 ) sampling interval still stands using our proposed method. Demonstrated by the experiment, the normalized root-mean-square error(NMSE) is 5.75%. Additionally, when the spatial sampling points are sampled randomly with 30% of the full sampling condition, this method can also restore and reconstruct the image with high quality. Due to the decrease of sampling points, the data volume can be reduced, which is beneficial for improving the scanning speed and alleviating the pressure of data transmission for near-field high resolution SAR imaging systems.