17 September 2019 in IEEE Transactions on Antennas and Propagation
We propose a hybrid dispersion compensation method to design wideband fixed-beam leaky-wave antennas (LWAs), with the tilting angle customizable in both forward and backward quadrants. In a previous work, a triangular dispersive prism constituted by metallic pins was presented to compensate for the dispersion of traditional LWAs and achieve a squint-free radiation in a relative bandwidth of 20%. However, that design suffered from the drawbacks of large geometry and limited angular range. To overcome these limitations, here a broadband gradient metasurface based on geometric phase theory is loaded in front of the prism to customize the radiation angle and reduce the total prism size. In addition, a novel ridged gap waveguide is employed to improve the linearity of LWA dispersion, which is beneficial to maintain the bandwidth of LWA with reduced size. Two examples are presented to demonstrate the excellent performance of the designed antennas. One antenna radiates at an angle of 39.5° in a squint-free bandwidth of 20%, but the prism size is decreased to a quarter of the original one, while the other realizes a broadside radiation with a squint-free bandwidth of 18%. Good agreement is exhibited between simulated and experimental results. The proposed method can be further extended to compensate for the dispersion of antenna arrays and improve the angular stability of the radiation beams in a large frequency band.
17 December 2019 in IEEE Transactions on Antennas and Propagation
In this paper, we propose a wideband fully-metallic impedance-matching horn lens antenna based on glide symmetry realized in the gap waveguide technology. A multiple iterative method is adopted, which overcomes the limitation of large phase deviations at the interface of traditional lens antennas, thus increases the directivity as a result. Moreover, the glide-symmetric configurations of inner metallic pins within the gap waveguide are employed to construct the artificial dielectric lens, with the advantage of the ultra-low dispersion, which is especially helpful to broaden the working bandwidth and improve the lens performance. The antenna is fed by a stepped double ridged gap waveguide which can easily excite the antenna working in a wide band. To reduce the undesired reflections at the antenna aperture, the antenna is ended with a tapered structure as an impedance transition. A prototype of the horn lens antenna is manufactured and measured, showing a broad operation bandwidth from 12 to 18.5 GHz with S11 less than -10 dB. The antenna can be further extended to the millimeter band due to the low losses of the gap waveguide at high frequencies and the iterative method can also be applied to other types of lens antenna designs.
18 November 2020 in IEEE Transactions on Antennas and Propagation
Leaky wave antenna is known as a type of travelling antenna with dispersive frequency responses, which has found important applications in modern communication, imaging and radar systems. The beam scanning rate is a key consideration in some applications, since it can minimize the bandwidth requirement of the system, during the scanning in broad angular regions. However, the sweeping linearity, namely the scanning angular range per unit frequency, is seldom taken into account at the same time in the published literature. In this article, we propose a waveguide-type leaky-wave antenna working from 11.1 GHz to 12 GHz. By loading periodical pins with glide symmetry in the waveguide, it is possible to manipulate the dispersion properties of the fast wave mode, hereby giving rise to a good balance between the scanning rate and sweeping linearity. This scenario has been validated by numerical simulation and experiment with excellent agreement. The measurement results reveal that the scanning angles have been increased to range from 16.7° ~67.5° varying the frequency from 11.1 to 12.1 GHz. The relative average scanning rate is enhanced up to 589.3°, with high sweeping linearity.
2 June 2021 in IEEE Transactions on Antennas and Propagation
In this article, a $1\times 12$ millimeter-wave (mmW) linearly tapered slot antenna (LTSA) array, fed by high-order waveguide modes, is introduced. Due to the antiphase characteristic between adjacent channels of a power divider based on the TE ${}_{2n,0}$ mode waveguide, the cross-polarized E-field components can cancel each other out in an endfire direction, even in the case of a relatively thick substrate. Moreover, the electric separations between the adjacent channels employed in a traditional substrate integrated waveguide (SIW) power divider can be removed without affecting the field distributions. This facilitates in improving robustness to avoid fabrication errors. Additionally, a general condition of generating a single high-order mode with symmetrical protection is outlined. By combining two antiphase TE 30 mode waveguides, an equivalent TE 60 mode waveguide with six identical output channels is realized. To feed a 12-element array, two equivalent TE 60 mode waveguides are employed as an equivalent TE 12,0 mode-feeding network. Instead of the complex 1-to- $n$ -way power divider and relatively thin substrate featured in previous works, the high-order mode-fed LTSA array introduced in this study is able to operate over 26.5–30 GHz with substrate height of 2 mm ( $0.19\lambda _{0}$ ), yielding a cross-polarization level of less than −15 dB.
15 September 2021 in IEEE Transactions on Antennas and Propagation
We propose a dual-polarized leaky-wave antenna (LWA) with orthomode based on a metallic square waveguide for broadband endfire radiation applications. Several double-sided slots acting as radiation elements are notched on the waveguide to produce an endfire pattern. To overcome the restriction associated with the endfire radiation condition of a linear array, a metallic core periodically loaded with pins is used to control the dispersion of the proposed double-sided-slot waveguide. By optimizing the height distribution of the loading pins along the longitudinal direction using a cosine function, stable endfire radiation can be achieved over a broad operating band. Moreover, dual-polarized radiation can be automatically implemented because of the rotational symmetry of the proposed LWA. Furthermore, two rectangular waveguides connected with a square waveguide are used as the orthomode transducer (OMT) of the proposed LWA. The numerical and experimental results verify that dual-polarized endfire radiation is achieved in the frequency range of 7.6–9.1 GHz with an isolation of higher than 45 dB. The realized gain achieved is in the range of 13–15 dBi with a cross-polarization level of below −30 dB.
5 May 2021 in IEEE Transactions on Antennas and Propagation
In this communication, a wideband Fabry–Pérot resonator antenna (FPRA) is proposed. An optimized partially reflective surface (PRS) with a transverse permittivity gradient (TPG) composed of four nonrotationally symmetric sections is employed in the design of the antenna. The use of nonrotationally symmetric PRS results in more than 31% improvement of the 3 dB gain bandwidth compared with the traditional rotationally symmetric PRS. Furthermore, two types of nonresonant metamaterials (metallic-ring and etching-hole unit cells) are used to implement the equivalent permittivity of PRS. In this way, the equivalent permittivity value covers a broad range (3.5–9.5) for the same dielectric. As a result, the restrictions imposed by the use of only commercially available dielectrics and the errors that occur during the fabrication and assembly progress of different materials can be avoided. The primary radiator of FPRA is a double-ridge waveguide horn, which ensures wideband antenna operation. An FPRA prototype is fabricated and measured, which exhibits a broad bandwidth (5.2–11.5 GHz) with the return loss |S 11 | of less than −10 dB. The measured 3 dB gain bandwidth is 73.8% (in the frequency range of 5.3–11.5 GHz) with a peak gain of 17.1 dBi at 7.8 GHz.