Coatings based on epoxy diane oligomer ED-20 are being developed as environmentally benign, foulingresistant marine coatings. Silver oxide and carbonate (mixture) was used as filler, the dispersion of which is 0.5 µm. It is proved that for the formation of composites with the improved physical and mechanical properties it is necessary to add Mechanical Mixture of Silver Carbonate and Oxide (MMSCO) in the amount of q = 0.050…0.250 pts. wt. into the epoxy diane oligomer ED-20 (100 pts. wt.). The obtained values of impact toughness of composites during the introduction of MMSCO into the binder increased by 2.5 times compared to the epoxy matrix. Moreover, the maximum capacity to resist impact loads, including fracture toughness, was demonstrated by the Composite Material (CM) with the filler content q = 0.050 pts. wt. Impact toughness of this CM is а = 18.53 kJ/m2. The developed materials and protective coatings based on them were used on the dry cargo ship Oles Honchar.
23 March 2016 in Molecular Crystals and Liquid Crystals
The effect of nano-fillers (carbon carbon nanotubes) on thermophysical properties of epoxy composites is investigated. The curve showing the dependence between the heat resistance of epoxy composite and the content of nanoparticles demonstrates the optimal content of carbon carbon nanotubes, indicating the improved performance characteristics of the material with the above content of carbon carbon nanotubes. To analyze the processes of structure formation and the behavior of composites under the influence of a thermal field, the thermal coefficient of linear expansion of materials is investigated. It is established that the thermal linear expansion coefficient of materials increases with an increase in temperature within different temperature areas under study. Additionally, the thermogravimetric (TGA) and differential thermal (DTA) analysis of the materials were conducted for the investigation of nanocomposites under elevated temperatures. The maximum values of endothermic and exothermic effects in composites depending on their filling are found.
20 August 2019 in Advances in Materials Science and Engineering
The corrosion resistance and hydroabrasive resistance of the developed epoxy composite coatings are investigated in this paper. The analysis of the penetration index change after τ = 50–150 days of immersion in a water medium and 10% sulfuric acid solution is carried out. The optimal ratio of the modifier and nanodispersed (Si3N4, Al2O3, AlN, and TiN) and fibrous (viscose, polyamide, matka silk, rong, and cashmere) fillers in the epoxy binder is determined. It was allowed to slow down the process of electrochemical reaction on the metal surface. The penetration of aggressive media in such a coating during the time t = 150 days is 0.8–2.8%. It is 1.5–2 times lower than the similar indexes of the initial epoxy matrix. The rational combination of the fibrous filler (wool, acrylic PAN, and cashmere), modifier, and nanodispersed (Si3N4, AlF3, IH, and ZrH) filler in the epoxy binder is found, which allows to provide optimum indexes of wear rate. The wear rate under the action of a hydroabrasive of such a coating is I = 0.20%, which is 4 times lower than the similar indexes of the initial epoxy matrix. The wear mechanism of such coatings is caused by the physical and mechanical processes of microcutting and plastic deformation of the surface layer of the material.
A new adhesive material and a restoration technology for marine equipment units are proposed. The optimal content of hardeners of different nature is found, and the effect of temperature conditions used for crosslinking epoxy resin DER-331, on the adhesive properties of the polymeric material is determined. The polymerization of the epoxy oligomer DER-331 and polyethylene polyamine (PEPA) hardener at a temperature T = 413 ± 2 K is found to enhance the adhesive properties of the polymeric material by 3.2–3.6 times, as compared to polymer GEN-150. In addition, the separation pattern of metal surfaces was analyzed, which allowed for an in-depth evaluation of the adhesive strength at separation and its variation upon increasing the content of hardeners introduced. Based on complex studies, it is shown that the developed polymeric adhesive should be used in the restoration of marine transport units, in particular, wheel fit in the compressor section of turbocharger.
9 October 2018 in Journal of Marine Engineering & Technology
The physical and mechanical properties of matrix based on epoxy resin ED-20 were investigated by adding unsaturated polyester resin ENYDYNE H 68372 TAE at different concentrations. The contents of polyester resin in the epoxy one by changing its concentration in the range of q = 10–120 mas.fr. were analysed. It was experimentally determined that matrix is characterised with its maximal rates of physical and mechanical properties with q = 10 mas.fr. of polyester resin ENYDYNE H 68372 TAE per 100 mas.fr. of ED-20. The received material is marked by the following indexes of physical and mechanical properties: fracture stresses during the flexion – σfl = 56.2 MPa, the modulus of elasticity during the flexion –E = 4.2 GPa, impact toughness –W = 12.8 kJ/m2. It was proved that indexes of modulus of elasticity and impact toughness during the flexion of developed composite are higher in 1.5–2 times, in comparison with the indexes of matrix which is based on the epoxy resin ED-20. The images of fracture of the composite materials were analysed through optical microscopy. It was determined that the results of investigation correlate with the obtained indexes of physical and mechanical properties, confirming their authenticity. The clearly defined heterogeneity of given polymers was not observed on the photos of fracture, which indirectly points on the compatibility of the ingredients of the binder, chosen for the study.
The impact of fillers in the epoxy oligomer on the test culture of the marine ecosystem was investigated. The content of additive—biocides—was selected based on the complex research using STAT-GRAPHICS® Centurion XVI. The ecotoxicity of composite surfaces was determined in model systems using methods which are standard in eco-microbiology. The microorganism was identified by studying morphological, cultural, biochemical, and antigenic properties. Studies of the structure and the microrelief of the surfaces of composite materials were conducted using scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy. Based on comprehensive research, it was established that the composition of oxytetracycline with content of q = 1.5 wt% and nanosilver with a content of q = 0.075 wt% per 100 wt% of the DER-331 oligomer and 10 parts by the mass of the TETA hardener ensures the formation of a porous nano-heterogeneous structure of the coating, which leads to the acceleration of the release of silver ions from the surface of the polymer. The rational content of the complex additives of biocides ensures adhesion to the cell wall of bacteria with subsequent penetration into it and subsequent change to the cell membrane, its death, and, therefore, the suppression of the fouling process of metal structures.