Yuxuan Du

Yuxuan Du


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 September 2022 in Metals
Verified
Journal Article
Open access
PDF file
YGYuShe Gao
YuShe Gao
XXXiangyi Xue
Xiangyi Xue
HGHuixian Gao
Huixian Gao
WLWenzhong Luo
Wenzhong Luo
KWKaixuan Wang
Kaixuan Wang
YDYuxuan Du
Yuxuan Du
Ti555211 titanium alloy is subjected to plastic deformation in the dual-phase (α + β phase) zone and single-phase (β phase) zone at various deformation temperatures and strain rates. High-temperature constitutive equations of the alloy in the dual-phase zone and single-phase zone are established in order to describe deformation behavior of the alloy in the different phase zones. By comparing the constitutive equation of the alloy in the dual-phase zone with that of the alloy in the single-phase zone, the deformation activation energy of the former was found to be higher than that of the latter. It is obvious that the deformation activation energy of α phase is obviously greater than that of β phase. Furthermore, the microstructural evolution of the alloy is different in the dual-phase zone and single-phase zone. When the alloy was subjected to plastic deformation in the dual-phase zone, the size of the grains in the β phase increased with the decreasing strain rate. When the alloy was subjected to plastic deformation in the single-phase zone, the size of the grains in the β phase considerably increased with the increasing deformation temperature. In particular, in the microstructures of the alloy subjected to plastic deformation in the single-phase region, the elongated grains can be observed at higher strain rates. Furthermore, it is more difficult for the alloy to induce plastic deformation in the dual-phase region than in the single-phase region.

7 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
HCHaisheng Chen
Haisheng Chen
FHFang Hao
Fang Hao
SHShixing Huang
Shixing Huang
JYJing Yang
Jing Yang
SLShaoqiang Li
Shaoqiang Li
XYXiaotong Yu
Xiaotong Yu
The formation and evolution of adiabatic shear behaviors, as well as the corresponding mechanical properties of a near-Ti-6Al-3Nb-2Zr-1Mo (Ti-6321) alloy during dynamic compression process, were systematically investigated by the split Hopkinson pressure bar (SHPB) compression tests in this paper. Ti-6321 samples containing three types of microstructures, i.e., equiaxed microstructure, duplex microstructure and Widmanstätten microstructure, were prepared to investigate the relationship between microstructures and dynamic mechanical behaviors under different strain rates in a range from 1000 s−1 to 3000 s−1. It was found by the dynamic strain–stress relation that the Ti-6321 alloys containing equiaxed microstructure, duplex microstructure and Widmanstätten microstructure all exhibited a strong strain-hardening effect. The samples containing equiaxed microstructure exhibited a larger flow stress than samples containing duplex microstructure and Widmanstätten microstructure. The adiabatic shearing behaviors in Ti-6321 alloy are significantly influenced by different types of microstructures. The formation of adiabatic shearing bands occurs in equiaxed microstructure when the strain rate is increased to 2000 s−1. The adiabatic shear bands are formed in duplex microstructure when the strain rate reaches 3000 s−1. However, the initiation of adiabatic shear bands is found in Widmanstätten microstructure under the strain rate of 1000 s−1. The Widmanstätten microstructure shows a larger sensitivity to adiabatic shearing than the equiaxed microstructure and duplex microstructure samples.

19 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
FHFang Hao
Fang Hao
YDYuxuan Du
Yuxuan Du
PLPeixuan Li
Peixuan Li
YMYouchuan Mao
Youchuan Mao
DLDeye Lin
Deye Lin
WWWilliamYi Wang
WilliamYi Wang
In the present work, the localized features of adiabatic shear bands (ASBs) of our recently designed damage tolerance α+β dual-phase Ti alloy are investigated by the integration of electron backscattering diffraction and experimental and theoretical Schmid factor analysis. At the strain rate of 1.8 × 104 s−1 induced by a split Hopkinson pressure bar, the shear stress reaches a maximum of 1951 MPa with the shear strain of 1.27. It is found that the α+β dual-phase colony structures mediate the extensive plastic deformations along α/β phase boundaries, contributing to the formations of ASBs, microvoids, and cracks, and resulting in stable and unstable softening behaviors. Moreover, the dynamic recrystallization yields the dispersion of a great amount of fine α grains along the shearing paths and in the ASBs, promoting the softening and shear localization. On the contrary, low-angle grain boundaries present good resistance to the formation of cracks and the thermal softening, while the non-basal slipping dramatically contributes to the strain hardening, supporting the promising approaches to fabricate the advanced damage tolerance dual-phase Ti alloy.

11 April 2023 in JOM
Verified
Journal Article
Closed access
PDF file
HCHaisheng Chen
Haisheng Chen
XLXianghong Liu
Xianghong Liu
YDYuxuan Du
Yuxuan Du
FHFang Hao
Fang Hao
JYJing Yang
Jing Yang
LLLei Lei
Lei Lei

3 February 2022 in Frontiers in Materials
Verified
Journal Article
Open access
FHFang Hao
Fang Hao
YDYuxuan Du
Yuxuan Du
WWWilliamYi Wang
WilliamYi Wang
YMYouchuan Mao
Youchuan Mao
JYJunlei Yin
Junlei Yin
JLJinshan Li
Jinshan Li
In the present work, the adiabatic shear characteristics of our recently designed α + β dual-phase Ti alloy at different strain rates have been investigated by hat shaped specimen. The deformation process is divided into three stages: work hardening stage, steady stage, and unstable thermal softening stage. Along or near the shear deformation paths, the microvoids and the cracks can be captured at the strain rate of 1.8 × 104 s−1, 2.0 × 104 s−1, and 2.3 × 104 s−1, both of which contribute to the stable and unstable softening. It is found that dynamic stored energy of cold work will be significantly improved by the enhanced high strain rate. In the view of coupling analysis of inverse pole figure and grain boundary map, it seems that low angle grain boundaries present a good resistance to the formation of cracks and thermal softening. On the contrary, high angles grain boundaries are typically located in ASBs and their affecting regions, which is in line with the reported results. While the geometrical necessary dislocation (GND) density of adiabatic shear band (ASB) and its surroundings increased significantly, the width of the ASB becomes wider as the strain rate increases, which is consistent with the theory of sub-grain rotation dynamic recrystallization model. The formation of multiple ASBs in the corner position is schematically illustrated and the average elastic modulus and hardness of the ASB region are lower than the α and β phases, combined with the GND analysis, which proves that the ASB is a thermal softening zone in this experiment.

1 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
YGYuShe Gao
YuShe Gao
XLXianghong Liu
Xianghong Liu
HCHaisheng Chen
Haisheng Chen
XXXiangyi Xue
Xiangyi Xue
HGHuixian Gao
Huixian Gao
YDYuxuan Du
Yuxuan Du
Hot workability and microstructural evolution of Ti-5.5Al-5Mo-5V-2Nb-1Fe-1Zr titanium alloy, which is also called Ti555211 titanium alloy, are investigated during compressive deformation at different temperatures and strain rates. It can be found that Ti555211 samples deformed at 750 and 850 °C comprised α and β phases, while Ti555211 samples deformed at 950 and 1050 °C consist of single β phase. When Ti555211 sample undergoes compressive deformation in the α + β phase region, microstructures of β phase vary more substantially than those of α phase, which means that plastic deformation of Ti555211 sample is governed by β phase. The process parameters are optimized by establishing processing maps based on dynamic material model. Ti555211 alloy generally possesses the better hot workability in the β phase zone. In the β phase zone of Ti555211 alloy, the best hot process area involves temperature range from 925 to 1025 °C and a strain rate range of 0.005 to 0.03 s−1.