Helene Katharina Baust

Ms. Helene Katharina Baust

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 December 2023 in Processes
Verified
Journal Article
Open access
PDF file
HBHelene Katharina Baust
Helene Katharina Baust
SHSimon Hammerich
Simon Hammerich
HKHartmut König
Hartmut König
HNHermann Nirschl
Hermann Nirschl
MGMarco Gleiß
Marco Gleiß
Solid–liquid separation is a fundamental operation in process engineering and thus an important part of many process chains in the preparation of slurries in the chemical industry and other parts of the industrial environment. For the separation of micron-sized particles which, due to their size, do not settle or settle very slowly in the earth’s gravity field, centrifuges are often used. The preferred choice are often decanter centrifuges because they work continuously and stabilize the process against product fluctuations due to their adjustment possibilities. The design of the apparatus is complex: The main components of the apparatus are the cylindrical-conical bowl, which rotates at a high speed, and a screw located inside the bowl, which rotates in the same direction at a low differential speed to transport the separated solids out of the apparatus. Geometrical properties of the apparatus, as well as the adjustable operating parameters, such as rotational speed or differential speed, have a significant influence on the separation. In practice, analytical models and the experience of the manufacturers form the basis for the design. Characteristics of the disperse phase, interactions with the liquid, as well as the influence of the flow on the separation, are not taken into account. As a consequence, the transfer to industrial scale always requires a large number of pilot-scale experiments, which are time-consuming and expensive. Due to the increasing computational power, computational fluid dynamics (CFD) provides one possibility to minimize the experimental effort in centrifuge design. In this work, the open-source software OpenFOAM is used to simulate the multi-phase flow in a laboratory decanter centrifuge. For validation, experiments were carried out on a laboratory scale and the main operating parameters, such as speed, differential speed, and volume flow rate, were varied. The simulation results show a good agreement with the experimental data. Furthermore, the numerical investigations show the influence of the flow on the separation of the particles. To evaluate the transportability of a material, the transport efficiency was introduced as a dimensionless parameter. In addition, the simulation allows the consideration of the individual velocity components, making it possible to generate an impression of the complex three-dimensional flow in the apparatus for the first time.

20 October 2022 in Processes
Verified
Journal Article
Open access
PDF file
Vasyl SkorychVasyl Skorych
Vasyl Skorych
MBMoritz Buchholz
Moritz Buchholz
MDMaksym Dosta
Maksym Dosta
HBHelene Katharina Baust
Helene Katharina Baust
MGMarco Gleiß
Marco Gleiß
Stefan HeinrichStefan Heinrich
Stefan Heinrich
The production of catalysts such as zeolites is a complex multiscale and multi-step process. Various material properties, such as particle size or moisture content, as well as operating parameters—e.g., temperature or amount and composition of input material flows—significantly affect the outcome of each process step, and hence determine the properties of the final product. Therefore, the design and optimization of such processes is a complex task, which can be greatly facilitated with the help of numerical simulations. This contribution presents a modeling framework for the dynamic flowsheet simulation of a zeolite production sequence consisting of four stages: precipitation in a batch reactor; concentration and washing in a block of centrifuges; formation of droplets and drying in a spray dryer; and burning organic residues in a chain of rotary kilns. Various techniques and methods were used to develop the applied models. For the synthesis in the reactor, a multistage strategy was used, comprising discrete element method simulations, data-driven surrogate modeling, and population balance modeling. The concentration and washing stage consisted of several multicompartment decanter centrifuges alternating with water mixers. The drying is described by a co–current spray dryer model developed by applying a two-dimensional population balance approach. For the rotary kilns, a multi-compartment model was used, which describes the gas–solid reaction in the counter–current solids and gas flows.

16 September 2023 in Separations
Verified
Journal Article
Open access
PDF file
LJLucas Jakob
Lucas Jakob
HBHelene Katharina Baust
Helene Katharina Baust
LGLukas Griesinger
Lukas Griesinger
HNHermann Nirschl
Hermann Nirschl
Aqueous two-phase flotation (ATPF) is an integrative downstream method for separating and concentrating biomolecules from crude biosuspensions such as fermentation broth. Its continuous operation not only increases throughput, but also makes it recommended for continuous upstreams. In this work, an optimized apparatus design in the form of a horizontal flotation tank is presented. The geometry of the new apparatus for continuous ATPF is optimized using flow simulations so that the two aqueous phases can be pumped uniformly through the flotation tank in co-current or counter-current flow. The implementation of a conductivity measurement enables to characterize the phase mixing effect induced by the rising gas bubbles introduced through three different gassing units. ATPF experiments with the model enzyme phospholipase A2 show that there are favorable combinations of gas flow rates to increase the flotation rate and reduce the back-diffusion at the outlet of the apparatus. This allows high phase exchange rates up to 2/h and hence increases the amount of enzymes that can be recovered per time. Co-current operation of continuous ATPF increased separation efficiency about 14% up to E = 74% compared to counter-current operation.

6 September 2022 in Separations
Verified
Journal Article
Open access
PDF file
HBHelene Katharina Baust
Helene Katharina Baust
SHSimon Hammerich
Simon Hammerich
HKHartmut König
Hartmut König
HNHermann Nirschl
Hermann Nirschl
MGMarco Gleiß
Marco Gleiß
The separation of finely dispersed particles from liquids is a basic operation in mechanical process engineering. On an industrial scale, continuously operating decanter centrifuges are often used, whose separation principle is based on the density difference between the solid and the liquid phase due to high g-forces acting on both phases. The design of centrifuges is based on the experience on the individual manufacturer or simplified black box models, which only consider a stationary state. Neither the physical behavior of the separation process nor the sediment formation and its transport is considered. In this work, a computationally-efficient approach is proposed to simulate the separation process in decanter centrifuges. Thereby, the open-source computation software OpenFOAM was used to simulate the multiphase flow within the centrifuge. Sedimentation, consolidation of the sediment, and its transport are described by material functions which are derived from experiments. The interactions between the particles and the fluid are considered by locally defined viscosity functions. This work shows that the simulation method is suitable for describing the solid-liquid separation in a simplified test geometry of a decanter centrifuge. In addition, the influence of the rheological behavior on the flow in the test geometry can be observed for the first time.

2 May 2024 in Chemengineering
Verified
Journal Article
Open access
PDF file
HBHelene Katharina Baust
Helene Katharina Baust
HNHermann Nirschl
Hermann Nirschl
MGMarco Gleiß
Marco Gleiß
Solid–liquid separation plays a decisive role in various industrial applications particularly in the treatment and purification of suspensions. Solid bowl centrifuges, such as the decanter centrifuge, are commonly employed in these processes as they operate continuously and enable high throughputs with short processing times. However, predicting the separation performance of solid bowl centrifuges proves to be challenging due to dynamic phenomena within the apparatus, such as particle settling, sediment build-up, consolidation and sediment transport. In practice, design considerations and the dimensioning of the apparatus rely on analytical models and the manufacturer’s expertise. Computational Fluid Dynamics (CFD) offers a way to deepen our understanding of these devices by allowing detailed examination of flow phenomena and their influence on the separation processes. This study utilizes the open-source software OpenFOAM to simulate multiphase flow in a laboratory-scale decanter centrifuge, solving individual transport equations for each particle size class. The basis is the characterization of the material through targeted laboratory experiments to derive material functions that describe the hindered settling and the sediment consolidation. Furthermore, experiments on a laboratory decanter served as validation. The results demonstrate the solver’s capability to replicate clarification and classification within the apparatus. Furthermore, the solver supports the definition of geometries tailored to specific separation tasks. This research demonstrates the potential of CFD for a better understanding of complex centrifuge processes and for optimizing their design to improve performance.