Neuromorphic computing and artificial neurons have been shown to improve the solution for some of the complex problems for conventional computers. We present a spiking soma Josephson junction-based soma (JJ-Soma) circuit that consists of a double-junction SQUID interfered with a resistor (threshold loop), a decaying superconductor loop cut by a resistor, which is coupled to the SQUIDlike structure. The proposed soma has three main properties: 1) ultrahigh-speed operation with minimal power consumption; 2) compatibility with standard foundry processes that allow fabrication with the available infrastructure; and 3) compatibility with conventional single flux quantum (SFQ) logic gates, which enables the design and implementation of complicated networks. Each soma circuit covers 40 µm × 80 µm area on-chip with different activation functions. The circuits are fabricated in a commercial foundry for superconductors and they have been implemented and demonstrated experimentally.
12 December 2012 in IEEE Transactions on Applied Superconductivity
Successful fabrication and demonstration of complex Rapid Single Flux Quantum (RSFQ) circuits depend heavily on the reliability of the cell library that is used for the design. In large-scale RSFQ integrated circuits, delay fluctuations (jitter) of each cell may occur due to fabrication tolerances. The fabrication-induced jitter of each cell might accumulate at each stage and bring out larger variations comparable with the designed delay. If such jitter is not considered while arranging timing of the circuit, it may cause the circuit to malfunction due to the shifting of SFQ pulses. Therefore, it is important to optimize and determine the delay fluctuations of each cell well before designing a large-scale integrated circuit. There are quite a number of parameters that affect the functioning and the performance of a logic gate; hence, an optimization tool is required. In this study, the progress on development of an optimization tool for a digital RSFQ cell library composed of fundamental logic gates, such as Josephson transmission lines, D-flip-flops, T-Flip-flops, splitters, and mergers are presented. Particle swarm optimization is used for an optimization algorithm, which determines the circuit parameters with minimum delay and/or jitter satisfying the required critical margin conditions.
ZnO thin films in nanorod (NR) and nanoflower (NF) morphologies were used as photoelectrode scaffolds for efficient visible-light-driven photoelectrochemical (PEC) water splitting process, where their decoration with copper indium gallium sulfide (CIGS) and indium sulfide () layers resulted in significant PEC performance enhancement. ZnO NF/CIGS/ photoelectrodes exhibited a remarkably high PEC efficiency ( applied bias photon-to-current efficiency, 83% incident photon-to-current efficiency) due to the negligible dark current, while ZnO NR/CIGS/ generated a photocurrent density of at 0.4 V (vs Ag/AgCl), being one of the highest performances reported in the literature for copper-based chalcopyrite photoelectrodes so far. The interfacial photoelectrode-electrolyte charge transport dynamics, investigated via intensity-modulated photocurrent spectroscopy, exhibited a sevenfold increase in charge transfer efficiencies with a significant drop in surface recombination kinetics for ZnO NF after CIGS/ decoration. The obtained results show consistency with numerically modeled electric field distribution profiles and electron paramagnetic resonance results of ZnO NF, rationalizing the enhanced charge transfer rates for decorated samples and confirming the defect passivating nature of CIGS/.
4 January 2013 in IEEE Transactions on Applied Superconductivity
Rapid single flux quantum technology is one of the most promising developments for future high-speed microprocessors, network routers, and analog-to-digital converters. This technology is based on well-timed signals and fast signal transmission. However, as the complexity of the circuits or the operating frequency of these signals increase, it becomes harder to achieve a successful timing scheme. Another case that prevents successful timing is thermal noise, which becomes more significant with the increase of the number of cells. Earlier studies on noise analysis show that the timing variations of the delay on a cascaded path vary up to 10% compared with the delay of the same type of single cell. On the other hand, circuit parameters may change during the fabrication process, and as a result, timing of the cell differs from the design value. For these reasons, we define a statistical model for the wiring cells, such as Josephson transmission lines, splitters, and mergers that can be used to calculate the timing delay and jitter instead of time-consuming simulations. We also discuss a possible method to identify the sensitive paths to the delay fluctuations among different alternatives. In this study, we analyze the delay and the jitter of cascaded combinations of the most common wiring cells to determine the correlation effect on delay and jitter between the consecutive gates. Then, we propose a statistical method to analyze these timings faster and easier. Finally, we discussed how to estimate the output probability of the clocked gates without performing an actual simulation.
18 September 2019 in Turkish Journal of Electrical Engineering and Computer Sciences
The many advantages of cryogenically cooled single-flux quantum (SFQ) circuits imply that the high speed and low voltage output signals must be amplified and interfaced with standard electronics. State-of-the-art low-noise and wide-band amplifiers are required to interface with room temperature electronics. One solution is to place preamplifiers at the cryogenic stage, which requires specific semiconductor design and fabrication. However, a more viable and energy-efficient approach is to integrate the pulsed logic circuit output stages with on-chip superconductor preamplifiers. We designed, fabricated, and tested an on-chip compact voltage multiplier integrated with the output stage of SFQ circuits to increase the voltage amplitude of SFQ pulses. The circuit is designed with the same technology as the logic circuit hence its noise level is lower, and it works at higher frequencies compared to complementary metal-oxide semi-conductor amplifiers and due to quantized nature of it there is no added noise. The fabricated circuit has a compact size of 160 µ m × 320 µ m and provides about 10 dB gain with measured 600 µ V output voltage at frequencies up to ∼25 GHz in simulations. By stacking more levels, over 20 dB gain at circuit level is achievable as shown in simulations. Moreover the gain of the superconductor voltage amplifier is quantized and programmable.