In order to predict flow behavior and find the optimum hot working processing parameters for 5754 aluminum alloy, the experimental flow stress data obtained from the isothermal hot compression tests on a Gleeble-3500 thermo-simulation apparatus, with different strain rates (0.1–10 s–1) and temperatures (300–500 °C), were used to construct the constitutive models of the strain-compensation Arrhenius (SA) and back propagation (BP) artificial neural network (ANN). In addition, an optimized BP–ANN model based on the genetic algorithm (GA) was established. Furthermore, the predictability of the three models was evaluated by the statistical indicators, including the correlation coefficient (R) and average absolute relative error (AARE). The results showed that the R of the SA model, BP–ANN model, and ANN–GA model were 0.9918, 0.9929, and 0.9999, respectively, while the AARE of these models was found to be 3.2499–5.6774%, 0.0567–5.4436% and 0.0232–1.0485%, respectively. The prediction error of the SA model was high at 400 °C. It was more accurate to use the BP–ANN model to determine the flow behavior compared to the SA model. However, the BP–ANN model had more instability at 300 °C and a true strain in the range of 0.4–0.6. When compared with the SA model and BP–ANN model, the ANN–GA model had a more efficient and more accurate prediction ability during the whole deformation process. Furthermore, the dynamic softening characteristic was analyzed by the flow curves. All curves showed that 5754 aluminum alloy showed the typical rheological characteristics. The flow stress rose rapidly with increasing strain until it reached a peak. After this, the flow stress remained constant, which demonstrates a steady flow softening phenomenon. Besides, the flow stress and the required variables to reach the steady state deformation increased with increasing strain rate and decreasing temperature.
To study the factors that affect the mechanical properties of materials, double-pass hot compression tests were performed under different deformation parameters using a Gleeble-3500 thermo-simulation machine. The static softening behavior of 5754 aluminium alloy during testing was analyzed by the 0.2% offset-stress method. The results show that the static softening fraction was greatly influenced by deformation parameters and rapidly increased with increasing delay time, strain rate and deformation temperature. In addition, a mesoscopic cellular automaton (CA) model was employed to simulate the microstructural evolution of the static recrystallization (SRX) during the double-pass hot compression test of the 5754 aluminium alloy. The results show that the SRX nuclei first formed along the grain boundaries, where the energy was sufficient, and deformation parameters had a significant influence on the SRX of the 5754 aluminium alloy. The recrystallized volume fraction increased with increasing temperature, strain rate, and delay time among deformation stages. The mean recrystallized grain size increased with increasing deformation temperature and delay time. However, the mean grain size was slightly reduced with an increase in the strain rate from 0.1 s−1 to 1 s−1 at constant temperature and delay time.
5 September 2019 in International Journal of Minerals, Metallurgy and Materials
The flow behavior of 5754 aluminum alloy was researched using the plane strain compression test for the range of 300–500 °C and 0.1–10 s−1. The experimental flow curves acquired directly from Gleeble-3500 show that deformation parameters have a significant effect on the flow curves. All curves show a broad peak due to the dynamic softening after the work hardening. In addition, the flow curves display a slight downward trend after reaching the peak stress at low and medium strain rates. This softening mechanism has been further investigated by the work hardening rate and the results show that the flow characteristics of 5754 aluminum alloy are mainly controlled by the mechanism of competition between hardening, dynamic recovery and continuous dynamic recrystallization. Based on the corrected true strain-stress curves, the constitutive model of the corresponding softening mechanism has been established by a linear regression method. Then, the developed model was embedded in the finite element (FE) analysis software (ABAQUS) by encoding the UHARD subroutine and the hot compression process of the alloy was simulated and analyzed. The simulation results show that the sample has an uneven flow in the deformation zone, which is consistent with the grain morphology of the corresponding region of the test sample. In addition, the simulated load-stroke values were well fitted to the experimental data. The predictive ability of the model was quantified by statistical indicators. It emerged that the FE of the embedded constitutive model effectively simulates the hot working process of 5754 aluminum alloy, which has reference value for actual processing.
Isothermal interrupted hot compression tests of 5754 aluminum were conducted on a Gleeble-3500 thermo-mechanical simulator at temperatures of 350 °C and 450 °C, and strain rates of 0.1 s−1 and 1 s−1. To investigate the metadynamic recrystallization behavior, a range of inter-pass delay times (5–60 s) was employed. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate, and delay times. These data allowed the parameters for the hot rolling process to be optimized. The dynamic softening at each pass and the effect of metadynamic recrystallization on flow properties and microstructural evolution were analyzed in detail. An offset yield strength of 0.2% was employed to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe the metadynamic recrystallization behaviors of the hot-deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.
Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.