Zhiwu Zhang

Dr. Zhiwu Zhang


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 May 2018 in Materials
Verified
Journal Article
Open access
PDF file
H Chang-Qing Huang
Chang-Qing Huang
XJXiaodong Jia
Xiaodong Jia
ZZZhiwu Zhang
Zhiwu Zhang
In order to predict flow behavior and find the optimum hot working processing parameters for 5754 aluminum alloy, the experimental flow stress data obtained from the isothermal hot compression tests on a Gleeble-3500 thermo-simulation apparatus, with different strain rates (0.1–10 s–1) and temperatures (300–500 °C), were used to construct the constitutive models of the strain-compensation Arrhenius (SA) and back propagation (BP) artificial neural network (ANN). In addition, an optimized BP–ANN model based on the genetic algorithm (GA) was established. Furthermore, the predictability of the three models was evaluated by the statistical indicators, including the correlation coefficient (R) and average absolute relative error (AARE). The results showed that the R of the SA model, BP–ANN model, and ANN–GA model were 0.9918, 0.9929, and 0.9999, respectively, while the AARE of these models was found to be 3.2499–5.6774%, 0.0567–5.4436% and 0.0232–1.0485%, respectively. The prediction error of the SA model was high at 400 °C. It was more accurate to use the BP–ANN model to determine the flow behavior compared to the SA model. However, the BP–ANN model had more instability at 300 °C and a true strain in the range of 0.4–0.6. When compared with the SA model and BP–ANN model, the ANN–GA model had a more efficient and more accurate prediction ability during the whole deformation process. Furthermore, the dynamic softening characteristic was analyzed by the flow curves. All curves showed that 5754 aluminum alloy showed the typical rheological characteristics. The flow stress rose rapidly with increasing strain until it reached a peak. After this, the flow stress remained constant, which demonstrates a steady flow softening phenomenon. Besides, the flow stress and the required variables to reach the steady state deformation increased with increasing strain rate and decreasing temperature.

24 May 2019 in Metals
Verified
Journal Article
Open access
PDF file
Xiaohui CuiXiaohui Cui
Xiaohui Cui
ZZZhiwu Zhang
Zhiwu Zhang
Hailiang YuHailiang Yu
Hailiang Yu
XXXiaoting Xiao
Xiaoting Xiao
YCYongqi Cheng
Yongqi Cheng
A three-dimensional (3D) finite-element model (FEM), including quasi-static stamping, sequential coupling for electromagnetic forming (EMF) and springback, was established to analyze the springback calibration by electromagnetic force. Results show that the tangential stress at the sheet bending region is reduced, and even the direction of tangential stress at the bending region is changed after EMF. The springback can be significantly reduced with a higher discharge voltage. The simulation results are in good agreement with the experiment results, and the simulation method has a high accuracy in predicting the springback of quasi-static stamping and electromagnetic forming.

26 July 2018 in Metals
Verified
Journal Article
Open access
PDF file
H Chang-Qing Huang
Chang-Qing Huang
XJXiaodong Jia
Xiaodong Jia
ZZZhiwu Zhang
Zhiwu Zhang
To study the factors that affect the mechanical properties of materials, double-pass hot compression tests were performed under different deformation parameters using a Gleeble-3500 thermo-simulation machine. The static softening behavior of 5754 aluminium alloy during testing was analyzed by the 0.2% offset-stress method. The results show that the static softening fraction was greatly influenced by deformation parameters and rapidly increased with increasing delay time, strain rate and deformation temperature. In addition, a mesoscopic cellular automaton (CA) model was employed to simulate the microstructural evolution of the static recrystallization (SRX) during the double-pass hot compression test of the 5754 aluminium alloy. The results show that the SRX nuclei first formed along the grain boundaries, where the energy was sufficient, and deformation parameters had a significant influence on the SRX of the 5754 aluminium alloy. The recrystallized volume fraction increased with increasing temperature, strain rate, and delay time among deformation stages. The mean recrystallized grain size increased with increasing deformation temperature and delay time. However, the mean grain size was slightly reduced with an increase in the strain rate from 0.1 s−1 to 1 s−1 at constant temperature and delay time.

9 April 2019 in Metals
Verified
Journal Article
Open access
PDF file
Xiaohui CuiXiaohui Cui
Xiaohui Cui
ZZZhiwu Zhang
Zhiwu Zhang
Hailiang YuHailiang Yu
Hailiang Yu
YCYongqi Cheng
Yongqi Cheng
XXXiaoting Xiao
Xiaoting Xiao
To compare with quasi-static uniaxial tensioning, researchers designed an electromagnetic uniaxial tension method using a runway coil. However, the requirements to obtain a uniformly deformed sample and the ways the stress changes on the sample using a runway coil have not been studied in the past. In this study, a three-dimensional (3D) sequential coupling method was developed to analyze the factors affecting on-sheet deformation inhomogeneity under electromagnetic uniaxial tension. Two main process parameters, comprising the die type and the relative position of the coil and sheet, were evaluated. Under the optimal parameters, the experiment and simulation both obtained uniformly deformed samples with different discharge conditions, and the simulation method had a high accuracy in modeling the deformation process. The stress state of the sample is approximately unidirectional tensile stress before 240 μs. After 240 μs, the three main stresses showed significant oscillations.