Kathleen Dunn

Prof. Kathleen Dunn

orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 January 2020 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Open access
PDF file
CNC. M. Netzband
C. M. Netzband
KDKathleen Dunn
Kathleen Dunn
Knowledge obtained on the mechanism for altering the Ce 3+ % on the ceria surface was used to create ceria slurries that polished thermal oxide with higher material removal rate (MRR) and lower post-polish roughness than slurries that are currently being used in industry. As described by the tooth-comb model, oxide removal occurs easiest at sites with fewer surface bonds. This allows for slurries to be prepared with particles of large size (68 nm) that have high MRR while obtaining roughness values that are equal to those of much smaller particles (5 nm). The addition of hydrogen peroxide initially increases the Ce 3+ % concentration on the particle surface, then decreases it. This trend is replicated by both MRR and roughness with improvements initially, until a threshold is reached, after which all of the metrics got worse. The effect of pH was more complex, as it impacts the polishing process in two ways, by governing the rate of the chemical reaction with ceria and also the rate at which silica hydrolyzes, which in turn determines the ease with which both chemical and mechanical removal occurs.

16 October 2019 in ECS Journal of Solid State Science and Technology
Verified
Journal Article
Open access
PDF file
CNC. M. Netzband
C. M. Netzband
KDKathleen Dunn
Kathleen Dunn
The ratio of Ce3+/Ce4+ on the surface of ceria CMP slurry abrasives was maximized by altering the slurries’ chemical environment. Maximizing this ratio increases the proportion of active Ce3+ sites which participate in removal reactions, leading to increased removal rates. Small amounts of peroxide and surfactant were added to three ceria slurries at varying pH values to determine how these chemicals affected the different particle surfaces. The effects of these chemicals on the oxidation ratio were determined through XPS analysis of the Ce 3d spectrum. The addition of surfactants to ceria slurry, while necessary to increase particle dispersibility, decreased the Ce3+/Ce4+ ratio and therefore limited chemical removal. Of the conditions tested, pH had no effect, surfactants decreased the ratio, and peroxide could either increase or decrease the ratio based on concentration. Understanding these interactions will help to inform the design of future ceria CMP slurries to maximize their effectiveness.

5 August 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
TJTao Jiang
Tao Jiang
SSSarabjot Singh
Sarabjot Singh
KDKathleen Dunn
Kathleen Dunn
Yanna LiangYanna Liang
Yanna Liang
Although various hydrometallurgical and solvometallurgical efforts have been made to extract REEs from end-of-life (EoL) products and waste, a systematic and statistical analysis of the impacts of leaching parameters to optimize the leaching process using organic acids is necessary, but lacking in the literature. This study employed the response surface methodology to develop mathematical models for optimal leaching by levulinic acid (LevA) of REEs in two waste materials, namely red mud and spent fluorescent lamp phosphors. The established models exhibited excellent statistical properties, in terms of significance, fitting, prediction, and error distribution. For red mud, the optimal conditions of liquid-to-solid ratio (L/S; v/w) of 40, temperature of 70 °C, and duration of 60 h led to 100% leaching of REEs excluding Sc. At the same L/S and temperature, >98.7% of REEs were leached from fluorescent phosphors after 96 h. The SEM–EDS analysis of the waste materials revealed and confirmed morphological and compositional changes after leaching under the optimal conditions.

2 December 2023 in Materials
Verified
Journal Article
Open access
PDF file
SSSarabjot Singh
Sarabjot Singh
KDKathleen Dunn
Kathleen Dunn
In the present study, the properties of Cu(Ag) alloy films were studied to evaluate their potential use as an alternate material for interconnection in hybrid bonding. Thin alloy films of Cu(Ag) were deposited by pulsed electrochemical deposition (PED) using a sulfuric acid-based bath, rotating disk electrode, and hot entry. Secondary ion mass spectrometry (SIMS) was used to measure the silver content of the films, with us finding that it decreases with increasing duty cycle. Thereafter, bright field scanning transmission electron microscope (STEM) imaging in combination with energy-dispersive x-ray spectroscopy (EDS) was used to visualize the thin film microstructure and to confirm the uniform distribution of silver throughout the film, with no bands being seen despite the pulsed nature of the deposition. Film resistance was measured by a four-point probe to quantify the impact of Ag content on resistivity, with us finding the expected linear relationship with the Ag content in the film. Furthermore, the coefficient of thermal expansion (CTE) of the films was measured using X-ray diffraction, and modulus and hardness were measured via nanoindentation, revealing linear dependences on the Ag content as well. Notably, the addition of 1.25 atom% Ag resulted in a significant increase in the CTE from 17.9 to 19.3 ppm/K, Young’s modulus from 111 to 161 GPa, and film hardness from 1.70 to 3.99 GPa. These simple relationships offer a range of properties tunable via the duty cycle of the pulsed plating, making Cu(Ag) a promising candidate for engineering wafer-to-wafer metal interconnections.

2 March 2023 in Nuclear Technology
Verified
Journal Article
Open access
BNBhavani Sasank Nagothi
Bhavani Sasank Nagothi
JAJohn Arnason
John Arnason
KDKathleen Dunn
Kathleen Dunn
Corrosion products in pressurized water reactors are challenging to study in situ, yet understanding their properties is key to improving reactor performance and radiation reduction. In this study, a hydrothermal synthesis technique was used to produce nickel ferrite (NiFe2O4) particles from goethite (α-FeOOH) and nickel nitrate hexahydrate [Ni(NO3)2 6H2O] in the presence of sodium hydroxide (NaOH). X-ray diffraction was used for phase identification, with scanning electron microscopy used for particle shape and size analysis. By varying the [Ni]:[Fe] ratio of the precursors and synthesis temperature between 100°C to 250°C, a phase diagram was developed to determine the stability field in both composition and temperature for obtaining a single-phase, nonstoichiometric nickel ferrite product. The compositional boundaries of the single-phase region of the diagram are a function of temperature, consistent with the increased solubility and reaction rates at temperatures above 125°C. The single-phase nickel ferrite encompasses [Ni]:[Fe] ratios in a very narrow range at 150°C, only 0.35 to 0.375, but widens as a function of temperature and reaches its greatest breadth at 250°C. At this temperature, a single-phase product is obtained for a range of starting compositions from 0.30 to 0.425. Outside of this window, additional nanoparticles are obtained whose identity and composition vary with both temperature and starting mixture. On the lower nickel content side of the single-phase region, the mixture contains either unreacted goethite (for temperatures below 200°C) or hematite (α-Fe2O3) at 200°C or higher. On the Ni-rich side of the single-phase region, theophrastite [β-Ni (OH)2] was obtained along with the nickel ferrite, at all temperatures studied. The single-phase window was widest at 250°C, resulting in nickel ferrites with a Ni mole fraction between 0.23 and 0.31.

15 March 2013 in ECS Transactions
Verified
Journal Article
Open access
PDF file
PHP.Y. Hung
P.Y. Hung
MWMatthew Wormington
Matthew Wormington
KMKevin Matney
Kevin Matney
PRPaul Ryan
Paul Ryan
KDKathleen Dunn
Kathleen Dunn
GBGennadi Bersuker
Gennadi Bersuker
High electron mobility III-V materials are strong candidates for nMOS transistors at the 11 nm technology node and beyond. Integrating III-V materials with Si (III-V/Si) is an attractive approach because it leverages the current Si-based manufacturing platform. However, the large lattice mismatch between III-V and Si leads to defects in the channel and compromises device performance and reliability. This paper explores two inline X-ray based characterization techniques, high resolution X-ray diffraction (HRXRD) and X-ray diffraction imaging (XRDI), to characterize defects in novel III-V/Si structures. The benefits and limitations of these techniques will be discussed.