Although various hydrometallurgical and solvometallurgical efforts have been made to extract REEs from end-of-life (EoL) products and waste, a systematic and statistical analysis of the impacts of leaching parameters to optimize the leaching process using organic acids is necessary, but lacking in the literature. This study employed the response surface methodology to develop mathematical models for optimal leaching by levulinic acid (LevA) of REEs in two waste materials, namely red mud and spent fluorescent lamp phosphors. The established models exhibited excellent statistical properties, in terms of significance, fitting, prediction, and error distribution. For red mud, the optimal conditions of liquid-to-solid ratio (L/S; v/w) of 40, temperature of 70 °C, and duration of 60 h led to 100% leaching of REEs excluding Sc. At the same L/S and temperature, >98.7% of REEs were leached from fluorescent phosphors after 96 h. The SEM–EDS analysis of the waste materials revealed and confirmed morphological and compositional changes after leaching under the optimal conditions.
In the present study, the properties of Cu(Ag) alloy films were studied to evaluate their potential use as an alternate material for interconnection in hybrid bonding. Thin alloy films of Cu(Ag) were deposited by pulsed electrochemical deposition (PED) using a sulfuric acid-based bath, rotating disk electrode, and hot entry. Secondary ion mass spectrometry (SIMS) was used to measure the silver content of the films, with us finding that it decreases with increasing duty cycle. Thereafter, bright field scanning transmission electron microscope (STEM) imaging in combination with energy-dispersive x-ray spectroscopy (EDS) was used to visualize the thin film microstructure and to confirm the uniform distribution of silver throughout the film, with no bands being seen despite the pulsed nature of the deposition. Film resistance was measured by a four-point probe to quantify the impact of Ag content on resistivity, with us finding the expected linear relationship with the Ag content in the film. Furthermore, the coefficient of thermal expansion (CTE) of the films was measured using X-ray diffraction, and modulus and hardness were measured via nanoindentation, revealing linear dependences on the Ag content as well. Notably, the addition of 1.25 atom% Ag resulted in a significant increase in the CTE from 17.9 to 19.3 ppm/K, Young’s modulus from 111 to 161 GPa, and film hardness from 1.70 to 3.99 GPa. These simple relationships offer a range of properties tunable via the duty cycle of the pulsed plating, making Cu(Ag) a promising candidate for engineering wafer-to-wafer metal interconnections.
In this study, the properties of Cu(Co) alloy films were investigated to assess their utility as an alternative material for interconnections in hybrid bonding applications. Thin films of Cu(Co) were deposited using electrochemical deposition in a standard sulfate-based electrolyte. X-ray photoelectron spectroscopy (XPS) of the films revealed that an increasing current density during deposition resulted in an increase in cobalt concentration. Bright-field scanning transmission electron microscopy (STEM) coupled with energy-dispersive x-ray spectroscopy (EDS) was used to visualize the fine-grained microstructure and confirmed grain boundary segregation of cobalt in the films. X-ray diffraction with a heated stage determined that the coefficient of thermal expansion (CTE) increased linearly with increasing cobalt content, from 17.5 ppm/K for pure copper to a maximum of 27.5 ppm/K for a film containing 24 at.% Co. Nanoindentation experiments found that the mechanical properties depended non-linearly on composition, with hardness increasing from 3.5 GPa for a 0% cobalt film to a maximum of 4.5 GPa (24 at.% Co) and the Young’s modulus increasing from 118 GPa to 214 GPa, respectively. Four-point probe electrical measurements confirmed the expected linear increase in resistivity as Co content increased. Since electrical and mechanical properties have differing dependences on the film composition, an optimal alloy composition that balances an acceptable increase in resistance with improved mechanical properties could enable more reliable, low-temperature bonding solutions in advanced microelectronic devices.