Mojdeh Nikpour

Dr. Mojdeh Nikpour

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2022 in Batteries
Verified
Journal Article
Open access
PDF file
MNMojdeh Nikpour
Mojdeh Nikpour
BLBaichuan Liu
Baichuan Liu
PMPaul Minson
Paul Minson
ZHZachary Hillman
Zachary Hillman
BMBrian A Mazzeo
Brian A Mazzeo
DWDean Wheeler
Dean Wheeler
The drying process of electrodes might seem to be a simple operation, but it has profound effects on the microstructure. Some unexpected changes can happen depending on the drying conditions. In prior work, we developed the multiphase-smoothed-particle (MPSP) model, which predicted a relative increase in the carbon additive and binder adjacent to the current collector during drying. This motivated us to undertake the present experimental investigation of the relationship between the drying rate and microstructure and transport properties for a typical anode and cathode. Specifically, the drying rate was controlled by means of temperature for both an NMC532 cathode and graphite anode. The material distribution was analyzed using a combination of cross-section SEM images and the energy-dispersive X-ray spectroscopy elemental maps. The binder concentration gradients were developed in both the in- and through-plane directions. The through-plane gradient is evident at a temperature higher than 150 °C, whereas the in-plane variations resulted at all drying temperatures. The measurements identified an optimum temperature (80 °C) that results in high electronic conductivity and low ionic resistivity due to a more uniform binder distribution. Trends in transport properties are not significantly altered by calendering, which highlights the importance of the drying rate itself on the assembled cell properties.

1 June 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
MNMojdeh Nikpour
Mojdeh Nikpour
NBN. Barrett
N. Barrett
ZHZ. Hillman
Z. Hillman
ATA. I. Thompson
A. I. Thompson
BMB. A. Mazzeo
B. A. Mazzeo
DWDean Wheeler
Dean Wheeler
Heterogeneity of porous electrodes can cause battery failure and performance deficiencies. On the other hand, some types of heterogeneity can improve performance. This study uses a multi-phase smoothed particle (MPSP) model, derived from smoothed particle hydrodynamics (SPH) and which is parameterized and validated by comparison with experimental viscosity, density, electronic conductivity, MacMullin number, and Young’s modulus of electrode films. The MPSP model simulates all major aspects of electrode production: mixing, coating, drying, and calendering, though the focus in this paper (Part 1) is on drying and calendering. Four types of electrodes are included in this study: a graphite anode and three traditional metal oxide cathodes. The model suggests how some types of heterogeneity can form during cathode and anode fabrication. The anode is more susceptible to mesoscale heterogeneities than the cathode due to differences in active particle shape and stiffness. The model and experiments show that regardless of the active material type, calendering increases the variability in electronic and ionic conductivity due to carbon and binder redistribution. This can be explained by means of the proposed multi-phase packing theory. On the other hand, calendering increases mechanical uniformity as also shown by model and experiment.

1 February 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
AHAmir-Sina Hamedi
Amir-Sina Hamedi
FPFezzeh Pouraghajan
Fezzeh Pouraghajan
FSFei Sun
Fei Sun
MNMojdeh Nikpour
Mojdeh Nikpour
DWDean Wheeler
Dean Wheeler
Lateral microstructure heterogeneity in anodes is known to induce nonuniform current density, state of charge, and lithium plating. This means that such electrode heterogeneity can limit the fast charging of lithium-ion batteries. In this work, a combination of experiments and simulation is employed to understand the effect of mm scale lateral heterogeneity on cell aging. A previously developed model was extended to efficiently simulate SEI formation and Li plating for independent regions of an electrode. The model consists of three parallel regions each described under a P2D framework and with a distinct ionic resistance and possibly active material loading. The results suggest that during fast charge when the active material is uniformly distributed across the three regions, the region with the highest resistance reaches the end of life sooner than the other regions. There is also positive feedback from Li metal filling the pores near the separator interface that further accelerates lithium plating. Finally, when there is a non-uniform active material distribution associated with the ionic resistance heterogeneity, tight competition between regions can occur, leading to less overall lithium plating and plating that is more uniform between regions.

1 December 2021 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
MNMojdeh Nikpour
Mojdeh Nikpour
BMB. A. Mazzeo
B. A. Mazzeo
DWD. R. Wheeler
D. R. Wheeler
This work is the extension of our previous paper [Nikpour et al., J. Electrochem. Soc. 168, 060547, (2021)] which introduced the multi-phase smoothed particle (MPSP) model. This model was used to simulate the evolution of the microstructure during the drying and calendering manufacturing processes of four different electrodes. The MPSP model uses particle properties to predict overall film properties such as conductivities and elastic moduli and is validated by multiple experiments. In this work, the model is used to investigate the effects of active material particle size, shape, orientation, and stiffness on graphitic anodes. The model predicts that smaller active particles produce higher calendered film density, electronic conductivity, MacMullin number, and Young’s modulus, as compared to larger active particles. Rod-shaped active materials have greater ionic transport and lower electronic transport compared to the disk and sphere shapes, which have similar transport properties. During calendering, disk-shaped particles tend to be oriented horizontally, which decreases through-plane ionic transport. Increasing the stiffness of the active material increases film porosity and composite Young’s modulus, while lowering electronic transport and increasing ionic transport.

1 January 2022 in Journal of the Electrochemical Society
Verified
Journal Article
Closed access
BLBaichuan Liu
Baichuan Liu
KPKayci Prugue
Kayci Prugue
MNMojdeh Nikpour
Mojdeh Nikpour
KWKristopher Ward
Kristopher Ward
BMBrian A Mazzeo
Brian A Mazzeo
DWDean Wheeler
Dean Wheeler
Heterogeneity of MacMullin number within battery electrodes is a key metric affecting cell performance. To characterize this heterogeneity, an aperture probe was developed. This probe, coupled with a newly developed transmission-line model, allows for measurements of tortuosity, represented by the MacMullin number, on millimeter length scales. Local MacMullin number values of seven electrodes were measured, and the ionic resistance profiles of these electrodes are given through contour maps of the MacMullin number. The method is validated by comparing the average MacMullin number to the value obtained through other measurement methods. The results show significant local MacMullin number variation in such electrodes on a millimeter length scale. This method will allow battery manufacturers and researchers to better quantify sources of heterogeneity and improve electrode quality.