Hydrothermal liquefaction (HTL) of biomass is establishing itself as one of the leading technologies for the conversion of virtually any type of biomass feedstock into drop-in biofuels and renewable materials. Several catalysis strategies have been proposed for this process to increase the yields of the product (biocrude) and/or to obtain a product with better properties in light of the final use. A number of different studies are available in the literature nowadays, where different catalysts are utilized within HTL including both homogeneous and heterogeneous approaches. Additionally, catalysis plays a major role in the upgrading of HTL biocrude into final products, in which field significant developments have been observed in recent times. This review has the ambition to summarize the different available information to draw an updated overall picture of catalysis applied to HTL. The different catalysis strategies are reviewed, highlighting the specific effect of each kind of catalyst on the yields and properties of the HTL products, by comparing them with the non-catalyzed case. This allows for drawing quantitative conclusions on the actual effectiveness of each catalyst, in relation to the different biomass processed. Additionally, the pros and cons of each different catalysis approach are discussed critically, identifying new challenges and future directions of research.

Hydrothermal liquefaction (HTL) is a thermochemical depolymerization technology, also known as hydrous pyrolysis, that transforms wet biomass into biocrude and valuable chemicals at a moderate temperature (usually 200–400 °C) and high pressure (typically 10–25 MPa). In HTL, water acts as a key reactant in HTL activities. Several properties of water are substantially altered as the reaction state gets closer to the critical point of water, which can result in quick, uniform, and effective reactions. The current review covers the HTL of various feedstocks, especially lignocellulosic and high protein-containing feeds with their in-depth information of the chemical reaction mechanisms involved in the HTL. Further, this review gives insight and knowledge about the influencing factors such as biomass pretreatment, process mode, process conditions, etc., which could affect the efficiency of the hydrothermal process and biocrude productivity. In addition, the latest trends, and emerging challenges to HTL are discussed with suitable recommendations.

Reverse osmosis and microfiltration are two membrane-based separation techniques that have gained popularity over the past few decades. A fundamental barrier to improving the overall efficiency of membrane separation is membrane fouling. The accumulation of foulants causes a reduction in permeate flux, a loss of selectivity and permeability, and a reduction in the membrane’s lifespan. Numerous chemical and physical surface changes have been studied to enhance membrane antifouling properties. Additionally, research has concentrated on creating membranes that use cutting-edge materials to improve their antifouling capability. This paper focuses on a wide-ranging and thorough analyses of the different types of fouling during wastewater treatment based on current research results regarding fouling control strategy and the potential of new methods for wastewater treatment. It is a further step forward for the evaluation of mitigation measures for emerging membrane fouling problems.

Hydrothermal liquefaction (HTL) is an emerging technology for bio-crude production but faces challenges in determining the optimal temperature for feedstocks depending on the process mode. In this study, three feedstocks—wood, microalgae spirulina (Algae Sp.), and hydrolysis lignin were tested for sub-supercritical HTL at 350 and 400 °C through six batch-scale experiments. An alkali catalyst (K₂CO₃) was used with wood and hydrolysis lignin, while e (Algae Sp.) was liquefied without catalyst. Further, two experiments were conducted on wood in a Continuous Stirred Tank Reactor (CSTR) at 350 and 400 °C which provided a batch versus continuous comparison. Results showed Algae Sp. had higher bio-crude yields, followed by wood and lignin. The subcritical temperature of 350 °C yielded more biocrude from all feedstocks than the supercritical range. At 400 °C, a significant change occurred in lignin, with the maximum percentage of solids. Additionally, the supercritical state gave higher values for Higher Heating Values (HHVs) and a greater amount of volatile matter in bio-crude. Gas Chromatography and Mass Spectrometry (GCMS) analysis revealed that phenols dominated the composition of bio-crude derived from wood and hydrolysis lignin, whereas Algae Sp. bio-crude exhibited higher percentages of N-heterocycles and amides. The aqueous phase analysis showed a Total Organic Carbon (TOC) range from 7 to 22 g/L, with Algae Sp. displaying a higher Total Nitrogen (TN) content, ranging from 11 to 13 g/L. The pH levels of all samples were consistently within the alkaline range, except for Wood Cont. 350. In a broader perspective, the subcritical temperature range proved to be advantageous for enhancing bio-crude yield, while the supercritical state improved the quality of the bio-crude.

Nickel-supported hierarchical zeolite catalysts were prepared through a desilication reassembly process under optimized conditions and applied in one-pot menthol synthesis. In this work, the hierarchical zeolite-supported metal bifunctional catalysts were prepared with the help of desilication re-assembly and wetness impregnation techniques and applied in menthol synthesis via citral hydrogenation. The prepared catalysts were characterized using PXRD, BET, FE-TEM, NH₃-TPD, H₂-TPR, pyridine adsorption, and ICP-OES techniques. As a result, the physicochemical and acidic properties, such as mesopore surface area, metal dispersion, acidity, catalytic activity, and strong Lewis acid sites of pure microporous ZSM-5/USY zeolites, were significantly improved. Consequently, with the occurrence of superior physicochemical and acidic properties, the Ni/HZ-0.5 M catalyst exhibited outstanding catalytic activity (100% conversion, TOF 7.12 h⁻¹) and menthol selectivity (83%, 4 h) with uniform stability at 100 °C, 1.0 MPa hydrogen. Similarly, the cracking rate decreased with the decrease in Bronsted acid sites.

This study primarily addresses the development of dynamic, selective and economical metal–acid (bifunctional) catalysts for one-pot menthol production by citral hydrogenation. Specifically, various metals such as Pd, Pt, Ni, Cs and Sn were doped over alumina support. Additionally, bifunctional composite catalysts were also prepared with the impregnation of heteropoly acids and Pd precursors over alumina support. Analytical techniques (e.g., BET, PXRD, FT-IR, pyridine adsorption and amine titration methods) were applied for characterization of the most efficient and selective catalysts (e.g., Al₂O₃ and PTA-Cat-I). Similarly, most of the essential operational variables (e.g., loading rate of metal precursor, type of heteropoly acid, temperature, gas pressure and reaction time) were examined during this study. The experimental data shows that the bifunctional catalyst (PTA-Cat-I) produced 45% menthol at full citral substrate conversion (r = 0.038 mmoles.min⁻¹) in liquid-phase citral hydrogenation (at optimized operating conditions: 70 °C, 0.5 MPa and 8 h). However, the heteropoly acid-supported bifunctional catalysts (e.g., PTA-Cat-I, PMA-Cat-I, SMA-Cat-I and STA-Cat-I) resulted in cracking and the dehydration of isopulegol/menthol by the generation of side products (e.g., 4-isopropyl-1-methyl, cyclohex-1-ane/ene); therefore, menthol yield was extensively diminished. On the other hand, non-acidic catalysts (e.g., Cat-I, Cat-II, Cat-III, Cat-IV and Cat-V) readily promoted hydrogenation reactions. The optimum menthol yield occurred due to the presence of strong Lewis and weak Bronsted acid sites. Mass transfer and reaction rate were substantially diminished due to acidity strength, heteropoly acid type and blockage of pores by the applied bifunctional catalysts.