Hydrothermal liquefaction (HTL) is a thermochemical depolymerization technology, also known as hydrous pyrolysis, that transforms wet biomass into biocrude and valuable chemicals at a moderate temperature (usually 200–400 °C) and high pressure (typically 10–25 MPa). In HTL, water acts as a key reactant in HTL activities. Several properties of water are substantially altered as the reaction state gets closer to the critical point of water, which can result in quick, uniform, and effective reactions. The current review covers the HTL of various feedstocks, especially lignocellulosic and high protein-containing feeds with their in-depth information of the chemical reaction mechanisms involved in the HTL. Further, this review gives insight and knowledge about the influencing factors such as biomass pretreatment, process mode, process conditions, etc., which could affect the efficiency of the hydrothermal process and biocrude productivity. In addition, the latest trends, and emerging challenges to HTL are discussed with suitable recommendations.

In this study, we synthesized hybrid systems based on manganese oxide@zinc oxide (Mn₃O₄@ZnO), using sol gel and hydrothermal methods. The hybrid materials exhibited hierarchical morphologies and structures characterized by the hexagonal phase of ZnO and the tetragonal phase of Mn₃O₄. The hybrid materials were tested for degradation of methylene blue (MB), methyl orange (MO), and malachite green (MG) under ultraviolet (UV) light illumination. The aim of this work was to observe the effect of various amounts of Mn₃O₄ in enhancing the photocatalytic properties of ZnO-based hybrid structures towards the degradation of MB, MO and MG. The ZnO photocatalyst showed better performance with an increasing amount of Mn₃O₄, and the degradation efficiency for the hybrid material containing the maximum amount of Mn₃O₄ was found to be 94.59%, 89.99%, and 97.40% for MB, MO and MG, respectively. The improvement in the performance of hybrid materials can be attributed to the high charge separation rate of electron-hole pairs, the co-catalytic role, the large number of catalytic sites, and the synergy for the production of high quantities of oxidizing radicals. The performance obtained from the various Mn₃O₄@ZnO hybrid materials suggest that Mn₃O₄ can be considered an effective co-catalyst for a wide range of photocatalytic materials such as titanium dioxide, tin oxide, and carbon-based materials, in developing practical hybrid photocatalysts for the degradation of dyes and for wastewater treatment.

Wastewater from the textile industry is chronic and hazardous for the human body due to the presence of a variety of organic dyes; therefore, its complete treatment requires efficient, simple, and low cost technology. For this purpose, we grew ZnO microstructures in the presence of psyllium husk, and the role of psyllium husk was to modify the surface of the ZnO microstructures, create defects in the semiconducting crystal structures, and to alter the morphology of the nanostructured material. The growth process involved a hydrothermal method followed by calcination in air. Additionally, the psyllium husk, after thermal combustion, added a certain value of carbon into the ZnO nanomaterial, consequently enhancing the photocatalytic activity towards the degradation of methylene blue. We also investigated the effect of varying doses of photocatalyst on the photocatalytic properties towards the photodegradation of methylene blue in aqueous solution under the illumination of ultraviolet light. The structure and morphology of the prepared ZnO microstructures were explored by scanning electron microscopy (SEM) and powder X-ray diffraction (XRD) techniques. The degradation of methylene blue was monitored under the irradiation of ultraviolet light and in the dark. Also, the degradation of methylene blue was measured with and without photocatalyst. The photodegradation of methylene blue is highly increased using the ZnO sample prepared with psyllium husk. The photodegradation efficiency is found to be approximately 99.35% for this sample. The outperforming functionality of psyllium-husk-assisted ZnO sample is attributed to large surface area of carbon material from the psyllium husk and the synergetic effect between the incorporated carbon and ZnO itself. Based on the performance of the hybrid material, it is safe to say that psyllium husk has high potential for use where surface roughness, morphology alteration, and defects in the crystal structure are vital for the enhancing the functionality of a nanostructured material. The observed performance of ZnO in the presence of psyllium husk provides evidence for the fabrication of a low cost and efficient photocatalyst for the wastewater treatment problems.

Aluminum nitride (AlN) is a semiconductor material possessing a hexagonal wurtzite crystal structure with a large band gap of 6.2 eV. AlN thin films have several potential applications and areas for study, particularly in optoelectronics. This research study focused on the preparation of Ni-doped AlN thin films by using DC and RF magnetron sputtering for optoelectronic applications. Additionally, a comparative analysis was also carried out on the as-deposited and annealed thin films. Several spectroscopy and microscopy techniques were considered for the characterization of structural (X-ray diffraction), morphological (SEM), chemical bonding (FTIR), and emission (PL spectroscopy) properties. The XRD results show that the thin films have an oriented c-axis hexagonal structure. SEM analysis validated the granular-like morphology of the deposited sample, and FTIR results confirm the presence of chemical bonding in deposited thin films. The photoluminescence (PL) emission spectra exhibit different peaks in the visible region when excited at different wavelengths. A sharp and intense photoluminescence peak was observed at 426 nm in the violet-blue region, which can be attributed to inter-band transitions due to the incorporation of Ni in AlN. Most of the peaks in the PL spectra occurred due to direct-band recombination and indirect impurity-band recombination. After annealing, the intensity of all observed peaks increases drastically due to the development of new phases, resulting in a decrease in defects and a corresponding increase in the crystallinity of the thin film. The observed structural, morphological, and photoluminescence results suggest that Ni: AlN is a promising candidate to be used in optoelectronics applications, specifically in photovoltaic devices and lasers.