Łukasz Bernat

Dr. Łukasz Bernat

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2012 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
MHM. Hajkowski
M. Hajkowski
ŁBŁukasz Bernat
Łukasz Bernat
Jakub HajkowskiJakub Hajkowski
Jakub Hajkowski
During design of the casting products technology, an important issue is a possibility of prediction of mechanical properties resulting from the course of the casting solidification process. Frequently there is a need for relations describing mechanical properties of silumin alloys as a function of phase refinement in a structure and a porosity fraction, and relations describing phase refinement in the structure and the porosity fraction as a function of solidification conditions. The study was conducted on castings of a 22 mm thick plate, made of EN AC-AlSi7Mg0,3 alloy in moulds: of quartz sand, of quartz sand with chill and in permanent moulds. On the basis of cooling curves, values of cooling rate in various casting parts were calculated. The paper also presents results of examination of distance between arms in dendrites of a solid solution α (DASL), precipitations length of silicon in an eutectic (DlSi) and gas-shrinkage porosity (Por) as a function of cooling rate. Statistical relations of DASL, DlSi, Por as a function of cooling rate and statistical multiparameter dependencies describing mechanical properties (tensile strength, yield strength, elongation) of alloy as a function of DASL, DlSi and Por are also presented in the paper.

4 February 2024 in Recycling
Verified
Journal Article
Open access
PDF file
ŁBŁukasz Bernat
Łukasz Bernat
TJTomasz Jurtsch
Tomasz Jurtsch
GMGrzegorz Moryson
Grzegorz Moryson
JMJan Moryson
Jan Moryson
GWGrzegorz Wiczyński
Grzegorz Wiczyński
The processing of copper-bearing scrap makes it possible to reduce the costs and energy consumption of obtaining copper alloy products compared to producing them from primary raw materials. To achieve this, it is necessary to quickly and accurately determine the content of alloying elements in individual scrap elements. However, the copper-bearing scrap obtained at secondary raw materials collection points consists of elements with various surface conditions (due to contamination, shape, paint coatings, roughness, etc.). The paper contains research results on the influence of surface roughness and paint coatings on the measurement result of the content of alloying elements in copper-bearing scrap. Three mobile spectrometers were used for measurements: spark-induced optical emission spectroscopy (OES), X-ray fluorescence spectrometry (XRF) and laser-induced breakdown spectroscopy (LIBS). The tests used elements with different surface roughness (from Ra = 0.03 μm to 6.7 μm) and covered with various types of varnish (alkyd, water-based, oil-phthalic, acrylic, oil-alkyd). It was found that the roughness of Ra < 2 μm does not significantly affect the results of the measurements with the OES and LIBS spectrometers, and a larger scatter of measurement results was observed for the XRF spectrometer compared to OES and LIBS. For Ra > 2 μm, a significant impact of roughness was found on the measurement results (this may result in the erroneous classification of the scrap as an incorrect material group). The influence of paint coatings on the measurement is much stronger compared to surface roughness. Even a single layer of paint can cause a change in the measurement result of the content of alloying elements by more than 10%. In the case of an OES spectrometer, paint coatings may prevent the measurement from being performed (which means that no measurement result can be acquired).

15 November 2019 in Archives of Foundry Engineering
Verified
Journal Article
Closed access
ŁBŁukasz Bernat
Łukasz Bernat
PPPawel Popielarski
Pawel Popielarski


1 July 2025 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
ŁBŁukasz Bernat
Łukasz Bernat
AKArkadiusz Kamil Kroma
Arkadiusz Kamil Kroma
This paper presents an analysis of FFF/FDM (Fused Filament Fabrication / Fused Deposiotion Modeling) applications for production of casting patterns used in sand casting, with particular emphasis on short-run and prototype production. For this purpose, casting patterns of different shape and...