Nupur Bihari

Ms. Nupur Bihari


Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 January 2017 in Materials
Verified
Journal Article
Open access
PDF file
HCHandy Chandra
Handy Chandra
SASpencer W. Allen
Spencer W. Allen
SOShane Oberloier
Shane Oberloier
NBNupur Bihari
Nupur Bihari
JGJephias Gwamuri
Jephias Gwamuri
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
Scientists have begun using self-replicating rapid prototyper (RepRap) 3-D printers to manufacture open source digital designs of scientific equipment. This approach is refined here to develop a novel instrument capable of performing automated large-area four-point probe measurements. The designs for conversion of a RepRap 3-D printer to a 2-D open source four-point probe (OS4PP) measurement device are detailed for the mechanical and electrical systems. Free and open source software and firmware are developed to operate the tool. The OS4PP was validated against a wide range of discrete resistors and indium tin oxide (ITO) samples of different thicknesses both pre- and post-annealing. The OS4PP was then compared to two commercial proprietary systems. Results of resistors from 10 to 1 MΩ show errors of less than 1% for the OS4PP. The 3-D mapping of sheet resistance of ITO samples successfully demonstrated the automated capability to measure non-uniformities in large-area samples. The results indicate that all measured values are within the same order of magnitude when compared to two proprietary measurement systems. In conclusion, the OS4PP system, which costs less than 70% of manual proprietary systems, is comparable electrically while offering automated 100 micron positional accuracy for measuring sheet resistance over larger areas.

14 August 2020 in Journal of Vacuum Science & Technology A
Verified
Journal Article
Closed access
PDF file
NBNupur Bihari
Nupur Bihari
IHIsmo T. S. Heikkinen
Ismo T. S. Heikkinen
GMGiovanni Marin
Giovanni Marin
CECraig Ekstrum
Craig Ekstrum
PMPierce J. Mayville
Pierce J. Mayville
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
3D printing offers enormous potential for fabricating custom equipment for space and vacuum systems, but in order to do this at low costs, polymers are necessary. Historically, polymers have not been suitable for these applications because of outgassing, but if coated with a conformal, inorganic film introduced with atomic layer deposition (ALD), then outgassing can be reduced. Previous work on coating ALD layers showed promise with heavily outgassing carbon black containing 3D printed polymers. In this study, ALD aluminum oxide and a commercially available vacuum sealant resin were used to coat clear, acrylonitrile butadiene styrene, polycarbonate, and polypropylene. Characterization of the films included spectroscopic ellipsometry for thickness, microstructure analysis with scanning electron microscopy, chemical analysis with energy-dispersive x-ray spectroscopy, and residual gas analysis to study relative change in outgassing. ALD-coated samples registered lower pressures than the resin-coated ones. The results showed that the ALD coatings could effectively inoculate unpigmented 3D printed plastics, which could be used in contamination-sensitive environments such as semiconductor processing systems and space environments.

14 April 2023
Verified
Book Chapter
Open access
PDF file
NBNupur Bihari
Nupur Bihari
IRIsmo Rauha
Ismo Rauha
GMGiovanni Marin
Giovanni Marin
CECraig Ekstrum
Craig Ekstrum
PMPierce Mayville
Pierce Mayville
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
Coating 3D printed plastic materials has been shown to be an effective method of reducing outgassing [1].

14 April 2023
Verified
Book Chapter
Open access
PDF file
NBNupur Bihari
Nupur Bihari
IRIsmo Rauha
Ismo Rauha
GMGiovanni Marin
Giovanni Marin
CECraig Ekstrum
Craig Ekstrum
PMPierce Mayville
Pierce Mayville
Joshua M. PearceJoshua M. Pearce
Joshua M. Pearce
Polymer-based materials used for 3D printing are often porous [1].